OS/400 Messages

Are you looking for the description of OS/400 (System i) messages e.g. CPF9801? Then you have come to the right place. Below you can see a (hoefully) complete list of of all OS/400 messages with all "second level texts".

Complete OS/400 Messages Documentation From CPIE002 up to DBE0000

This documentation is copyright by IBM.
Count: 11223 Skipped: 0
OS/400 Messages
Description
SNA over IPX job QAPPCIPX ending.
IPX circuit changed, but has subsequently been removed.
&1 has not completed for IPX circuit &2.
IPX circuit route added, but has subsequently been removed.
QIPX job could not inform user job of circuit status.
SNA over IPX location name not resolved.
SNA over IPX job QAPPCIPX successfully started.
IP over IPX job QAPPCIPX not started.
IPX circuit &1 no longer exists.
Line description &1 no longer exists.
IP over IPX activated.
IP over IPX activated; however, all interfaces not started.
IP over IPX deactivated.
Line description &1 no longer exists.
SNA over IPX job QAPPCIPX submitted.
IPX support is not responding.
IPX circuit route changed, but has subsequently been removed.
IPX circuit service added, but has subsequently been removed.
IPX circuit service changed, but has subsequently been removed.
No circuit routes
No circuit services
No associated routes
No routes
No connections
No associated services
No services
Error occurred on IPX circuit &1.
No address entries
IPX circuit &1 has no associated routes.
IPX circuit &1 has no associated services.
No circuits
Circuit and IPX description datagram sizes do not match.
Verifying connection to remote system at network number &1, node address &2.
No response from remote system within &1 seconds for connection verification &2.
QIPX job &1/&2/&3 started.
Initial processing of QIPX job &1/&2/&3 complete.
Parameter &1 not supported by IPX circuit &4.
IW2TMRRTY has been reset for IPX circuit &1.
IW2TMRITV has been reset for IPX circuit &1.
IPXNETNBR has been removed from circuit &1.
BIND command to an Integrated PC Server failed.
Additional information available.
No email address is available in the contact database.
Service Monitor detected a software problem.
Service Agent is analyzing your system product activity log entries.
Service Agent is not able to send a service request - action required.
Service Agent has sent a service request with service assigned number &1.
Service Agent will expire on &1 (MDY date format) - action required.
Service Agent has expired - action required.
Service request for problem &1 not sent - action required.
Service Agent not able to send a service request - action required.
Service Agent is disabled - action required.
Error working with problem &1.
PTF &1 downloaded for problem &2.
Service Agent job &1 in subsystem QSYSWRK has started successfully.
Service Agent problem reporting is active for &1.
Service Agent line control did not complete successfully.
Service Agent data queue &1 created.
Service Agent expired on &1 (MDY date format) - action required.
Service Agent has placed an automated operational test request with service assigned number. &1.
Service Agent program &1 encountered an error - action required.
Service Agent was unable to send a message to user &1.
Service Agent program &1 was unable to use file &3.
Service Agent created problem
Service Agent Auto PTF function has been disabled.
Configuration changes are needed for the Service Agent Auto PTF function - action required.
PTFs not downloaded by Service Agent Auto PTF function - action required.
Service Agent Auto PTF function needs to be configured - action required.
&1 &2
Service Agent Auto PTF function has started.
Service Agent Auto PTF function cannot continue - action required.
Service Agent Auto PTF order failed - action required.
PTF &1-&2 downloaded. Load and apply this PTF.
Service Agent has created a problem log entry for ordering PTF &1-&2 - action required
Service Agent has determined that no new PTFs are needed.
Service Agent has determined that PTF &1-&2 is required. Please load and apply this PTF.
Service Agent has requested PTF &1-&2. Please load and apply this PTF when it arrives.
PTFs requested by Service Agent will be sent on media.
PTF &1-&2 cover letter downloaded.
Service Agent has requested the cover letter for PTF &1-&2.
PTF cover letters requested by Service Agent will be sent on media.
Service Agent dynamic threshold table update using the Auto PTF function failed.
Service Agent Auto PTF function cannot continue - action required.
Service Agent automated operational test function has started.
Service Agent monitoring jobs need to be ended and restarted.
Blackout period recorded successfully.
No blackout period active.
Blackout period cancelled.
Error occurred while processing &1.
Entry not found.
Unexpected error while working with the selected record.
Could not delete spooled file.
Print request completed.
List processing error.
Application failure.
Cannot retrieve information from selected list entry.
Error accessing event file.
Error building list.
Panel display failed.
List not deleted.
Requested record not found.
Dialog list error.
Automated operational test schedule day not valid.
Service Agent activation did not complete.
Electronic Service Agent subsystem jobs not started.
Service Agent has detected excessive reportable problems.
Error reporting problem &1. Retry limit reached.
An error occurred during Service Agent process &1.
Service Agent service information process &1 completed successfully.
Warnings have been issued for Service Agent service information collection process &1.
An error occurred while testing ECS communications to the service provider.
Verify operation completed successfully.
Verify operation not successful.
The process of collecting and/or sending service information to IBM has been started.
Licensed Internal Code error.
9331 diskette unit is being assigned; please wait
Test is running; please wait
Running test unit 1
Running test unit 2
Running test unit 3
Running test unit 4
Running test unit 5
Running test unit 6
Running test unit 7
Detected AC loss
Air Moving Device Fault
Air Moving Device missing error
Distributed Data Interface Network Adapter
I/O card Licensed Internal Code module AJGRW601
Controller &26 indicates error on disk unit.
Disk bus interface error occurred
9337 Service Information
9337 Controller Card
9337 Connector Panel
Cryptographic processor LIC is at an improper state
Cryptographic processor Licensed Internal Code failed
Cryptographic processor LIC detected a problem
Cryptographic processor load request failure
Domain Regulator
Domain 29V Buss
SPCN card
Cryptographic I/O processor
Crytographic Licensed Internal Code
Security system Licensed Internal Code
Local Distributed Data Interface Adapter cable
Severe error detected by I/O card Licensed Internal Code
One of the internal data path configurations failed
Link Confidence Test failed on PORT A
Physical connection mgmt for PORT A was not able to proceed
Optical bypass switch is stuck in bypassed position
Link error rate threshold was exceeded
Station has entered a wrapped configuration
Active port has switched from primary to backup connection
I/O card Licensed Internal Code module AJGFW903
Distributed Data Interface Network Adapter card error
Distributed Data Interface Adapter; remote station error
System to security interface unit cable
4754 security interface unit
IBM personal security card
X.25 restart negotiation failed
PLC/HDLC DTE/DCE mode configured not valid
SABM response or UA command received
Protocol mismatch during link initialization
X25DCE value in CRTLINX25 command
Incorrect configuration data for Frame Relay LIC
Frame Relay I/O adapter card storage not available
Too many frames with bad receive sequence counts
Distributed Data Interface tests are running. Please wait.
Jobs must be ended before testing can continue.
DTE/DCE role negotiation not valid for leased line
ACRSRCNAME value in CRTNWIFR command
AUTOANS, AUTODIAL, SWTCNN, CNN values in CRTNWIFR command
CTSTMR value in CRTNWIFR command
INTERFACE value in CRTNWIFR command
LINESPEED value in CRTNWIFR command
MAXFRAME value in CRTNWIFR command
MAXOUT value in CRTNWIFR command
NRZI value in CRTNWIFR command
RSRCNAME value in the CRTNWIFR command
SNBU, MODEMRATE, DUPLEX values in CRTNWIFR command
Broadcast addresses are not supported at this time.
Station has recovered from a wrapped configuration
Link Confidence Test failed on PORT B
Physical connection mgmt for PORT B was not able to proceed
An undesirable connection attempt on PORT A has been made
Distributed Data Interface Network
Optical Bypass Switch
PTF is required to enable requested nettype
An undesirable connection attempt on PORT B has been made
PORT A link has been terminated due to high error rate
PORT B link has been terminated due to high error rate
Required PTF is not installed
Ring insertion test is running. Please wait.
Testing is complete on Port A, move wrap plug to Port B.
APPC error.
No dial tone detected on telephone line
Ring back tone not detected
Call failure. Adapter is not connected to telephone line.
Telephone cable
FAX coupler
Data communications equipment
Communication failure while sending or receiving data
Licensed program is not installed or working incorrectly
Fax coupler error detected
Fax application program
Broadcast Addresses not supported for Destination SAP
Broadcast Addresses not supported for Source SAP
Invalid value for LNNCNNTMR, please re-enter
Invalid value for LNNCNNRTY, please re-enter
Processor tests in progress, please wait
NWSD does not exist, please enter another value
Line is attached to an Integrated Server, please re-enter
Address cannot be changed for Frame Relay direct lines
Only the objects that you are authorized to are displayed.
You are not authorized to use this object, select another
I/O processor Licensed Internal Code
Communications Input/Output Processor card
Communications Input/Output Adapter card
Storage card
I/O processor or communications IOA card failed
I/O processor memory error - bad memory module.
I/O processor detected a recoverable error.
I/O processor detected an error on one port.
A Virtual DASD Device Driver error was detected.
Server Storage Space Object
I/O processor detected a NetBIOS Device Driver error.
I/O processor detected an Interconnect Device Driver error.
Operating system portion of LAN Server/400 Configuration.
LAN Server/400 Administration
Not valid system configuration detected
Local area network adapter card
I/O processor Licensed Internal Code
I/O processor Licensed Internal Code
Local area network I/O adapter port not operational.
Initialization completed; error trying to open adapter.
I/O adapter Licensed Internal Code
Communications adapter Licensed Internal Code failed
Communications Console Cable
Wrap connector
Bridge card
ATM Input/Output adapter card
Main storage dump must be copied for service.
System portion of Network Server configuration.
NetWare Integration for operating system configuration.
Memory error - bad DIMM.
I/O adapter resource not available.
I/O adapter error; logged only.
An I/O adapter failure occurred.
An error was detected on one of the attached adapter cards.
I/O adapter Licensed Internal Code failed.
One half of I/O adapter failed.
AIX Operating System
AIX Server Device Driver
Other AIX Device Drivers and kernel extensions
User-initiated action
SCSI jumper card was not detected.
Incorrect SCSI jumper card detected
Incorrect, defective or missing SCSI jumper card
Incompatible hardware detected.
Network not responding.
Optical Media
AIX Operating System, Device Driver or kernel extensions
Storage Management failed to reach full paging.
Missing DASD units.
Auto copy failed or not attempted.
System ASP threshold exceeded after auto copy done.
Configured line speed not supported by network.
Configuration of DUPLEX parameter not supported by network.
Unable to establish a network link.
LINESPEED value in CRTLINETH command.
DUPLEX value in CRTLINETH command.
Integrated PC Server mouse
Integrated PC Server keyboard
Integrated Netfinity Server display
Integrated PC Server external cable
Device Driver
Windows Operating System
Optical Library drive cabling
Optical Library optical drive
No description is available
DIMM 0
DIMM 1
DIMM 2
DIMM 3
DIMM in first populated DIMM position
IOP DIMM
Remote HSL Network Bus
Direct Attach Netfinity Server
Direct Attach Netfinity Server cable
No entry in volume statistics log; enter volume ID again.
Tape is good; enter another volume ID to analyze or press F3
Tape is worn; enter another volume ID to analyze or press F3
Not authorized for PRTERRLOG; press Enter.
Analyzing tape volume. This may take several minutes.
Power Supply P01 error
Power Supply P02 error
Power Supply P03 error
Power Supply P04 error
Power Supply P05 error
Power Supply P06 error
Power Supply P01 Power Fault
Power Supply P02 Power Fault
Power Supply P03 Power Fault
Power Supply P04 Power Fault
Power Supply P05 Fault
Power Supply P06 Fault
Regulator R01 error
Regulator R02 error
Regulator R03 error
Regulator R04 error
Regulator R05 error
Regulator R06 error
Regulator R07 error
Regulator R08 error
Regulator R09 error
Regulator R10 error
Regulator R11 error
Regulator R12 error
Regulator R13 error
Regulator R14 error
Regulator R15 error
Regulator R16 error
Regulator R17 error
Regulator R18 error
Regulator R19 error
Regulator R20 error
Regulator R21 error
Regulator R22 error
Regulator R23 error
Configuration Requires 200V Input
Regulator R01 Fault
Regulator R02 Fault
Regulator R03 Fault
Regulator R04 Fault
Regulator R05 Fault
Regulator R06 Fault
Regulator R07 Fault
Regulator R08 Fault
Regulator R09 Fault
Regulator R10 Fault
Regulator R11 Fault
Regulator R12 Fault
Regulator R13 Fault
Regulator R14 Fault
Regulator R15 Fault
Regulator R16 Fault
Regulator R17 Fault
Regulator R18 Fault
Regulator R19 Fault
Regulator R20 Fault
Regulator R21 Fault
Regulator R22 Fault
Regulator R23 Fault
29V Buss Fault
2.5V Processor Regulator Fault
3.3V Processor Regulator Fault
2.5V Memory Control Regulator Fault
3.3V Memory Control Regulator Fault
3.3V Memory 1 Control Regulator Fault
3.3V Memory 2 Control Regulator Fault
Cache Regulator Fault
Processor 1 Regulator Fault
Processor 2 Regulator Fault
Control Supply 5VSW Regulator Fault
Internal Battery Power Unit Charger Fault
Internal Battery Power Unit Fault
Internal Battery Power Unit or Charger Fault
Internal Battery Power Unit Charger Fault
External Battery Power Unit Charger Fault
External Battery Power Unit Fault
External Battery Power Unit or Charger Fault
Clock Card Failure
Clock Regulator Fault
No VPD Found due to Invalid Bypass
Timeout on Panel for Request of VPD
No VPD Found due to Clock Card Failure
VPD Critical Mismatch
Processor Unit VPD Mismatch
Invalid Cache Jumper
Cache Voltage Mismatch
No Processor Installed
Invalid Processor VPD
No Processor VPD
AC Loss to Power Supply P01 or Power Supply P01 Failure
AC Loss to Power Supply P02 or Power Supply P02 Failure
AC Loss to Power Supply P03 or Power Supply P03 Failure
AC Loss to Power Supply P05 or Power Supply P05 Failure
AC Loss to Power Supply P06 or Power Supply P06 Failure
No Power Supplies Present
Power Supply P01 fault/AC loss
Power Supply P01 fault
Power Supply P01 Communication fault
Power Supply P02 fault/AC loss
Power Supply P02 fault
Power Supply P02 Communication fault
Power Supply P03 fault/AC loss
Power Supply P03 fault
Power Supply P03 Communication fault
Power Supply PP1 Air Moving Device fault
Power Supply PP2 Air Moving Device fault
Battery Charger Load fault
Regulator Fault on Card Position M01
Regulator Communication Fault on Card Position M01
Processor/Memory Card not installed
Processor Regulator fault
Regulator Fault on Card Position M06
Regulator Communication Fault on Card Position M06
SPCN Frame-to-Frame Communication fault
Load fault on the +12V bus
Load fault on the +5V bus
Load fault on the +3.3V bus
Load fault on the -12V bus
Load fault on the +1.8V bus
Load fault on the +2.5V bus
Load fault on the +12V/-12V bus
Load fault on the +3.3V/+1.5V bus
Load fault on the +1.5V/+1.3V bus
Battery Power Unit 1 and 2 Failed
Broadcast Addresses not supported for remote adapter address
2.5V Processor Domain Fault
3.3V Processor Domain Fault
2.5V Memory Control Domain Fault
3.3V Memory Control Domain Fault
3.3V Memory Control 1 Domain Fault
3.3V Memory Control 2 Domain Fault
Cache Regulator Domain Fault
Processor 1 Regulator Domain Fault
Processor 2 Regulator Domain Fault
Clock Regulator Domain Fault
Power Good Fault
Optical Converter 5V Fault
Domain 1 Fault
Domain 2 Fault
Domain 3 Fault
Domain 4 Fault
Power Supply PP1 fault/AC loss
Power Supply PP1 fault
Power Supply PP1 Communication fault
Power Supply PP2 fault/AC loss
Power Supply PP2 fault
Power Supply PP2 Communication fault
Unable to Collect VPD
Memory Module Misplug
Battery Charger Unit missing
SPCN Configuration mismatch
SPCN Default Configuration loaded
No SRC translate
External Netfinity Server 3.3V fault
External Netfinity Server Power Good fault
Integrated Netfinity Adapter fault
External Netfinity Server R485 Communication fault
Reference the Problem Analysis Guide for the SRC displayed.
I2C Bus Controller Communication fault
I2C Bus 1 Communication fault
I2C Bus 2 Communication fault
I2C Bus 3 Communication fault
I2C Bus 4 Communication fault
I2C Bus 5 Communication fault
I2C Bus 6 Communication fault
I2C Bus DASD Backplane 1 Communication fault
I2C Bus DASD Backplane 2 Communication fault
I2C Bus DASD Backplane 3 Communication fault
I2C Bus Adapter Communication fault
I2C Bus PCI Backplane Communication fault
I2C Bus Panel Communication fault
I2C Bus Fan Local Controller Communication fault
I2C Bus Fan Remote Controller Communication fault
I2C Bus SPCN VPD Communication fault
I2C Bus Device Backplane 4 Communication fault
Thermal calibration in progress
BPA A AC loss
BPA B AC loss
BPC A communication failure
BPC B communication failure
A DCA or fan has dropped to N-mode status in MCM subsystem
BPC download failure on BPA A
BPC download failure on BPA B
BPC A cable missing
BPC B cable missing
Cage air flow cooling problem
BPA-A to BPA-B communication fault
Critical logic overtemperature
BPR-1 communication fault
BPR-2 communication fault
BPR-3 communication fault
BPA 350V power failure
BPC to BPD-1 communication fault
BPC to BPD-2 communication fault
BPC to BPR-1 communication fault
BPC AC power loss or phase missing
BPC Room EPO switch has been detected open
BPC UEPO switch is in the bypass position
BPA FRU failure not isolated
BPC fault
BPC Seeprom VPD fault
BPF Fan fault
BPD-1 fault
BPD-1 Seeprom VPD fault
BPD-2 fault
BPD-2 Seeprom VPD fault
BPC to BPR-2 communication fault
BPC to BPR-3 communication fault
BPR-1 fault
BPR-1 Seeprom VPD fault
BPR-2 fault
BPR-2 Seeprom VPD fault
BPR-3 fault
BPR-3 Seeprom VPD fault
MCM running over temperature
Airflow loss in MCM subsystem resulting in over-temperature
No MCMs detected or MCMs mismatch
Processor over-temperature detected
Error not isolated; VPD on BPR may be corrupted
Hardware configuration cannot support N-mode power
BPA EPO Switch fault
2.5V bus processor subsystem load fault
1.8V bus processor subsystem load fault
1.5V bus processor subsystem load fault
3.3V bus processor subsystem load fault
5.0V bus processor subsystem load fault
Processor DCA-1 fault
Processor DCA-1 Seeprom VPD fault
Processor DCA-1 cable fault
Processor DCA-2 fault
Processor DCA-2 Seeprom VPD fault
Processor DCA-2 cable fault
Processor DCA-3 fault
Tape path dirty or write data check error
Tape path dirty or write identification record error
Tape path dirty or read data check error
Tape path dirty or read identification record error
Recoverable tape unit failure; logged only
Tape unit failure
Volume statistics; logged only
Device error reported; tape I/O processor
Write Protect violation reported by tape unit; logged only
Tape
I/O device
I/O device not communicating
Operator's manual
Refer to I/O device maintenance manual
Magnetic Tape Subsystem Operator's Guide
Tape unit &25 failed with a media error.
Tape I/O processor card or Licensed Internal Code error
Tape I/O processor card error
System processor card or tape I/O processor card error
I/O processor resource not available
Not valid condition in I/O processor Licensed Internal Code
I/O processor card or Licensed Internal Code error
Tape unit &25 failed.
Repeated single bit equipment error; corrections occurred
Error log full; process other codes first
Device not ready during IPL
I/O command from tape not valid
Tape too short
Wrong tape loaded or tape media error.
Tape I/O processor card, tape drive, or Lic Int Code error
Tape I/O adapter card error; logged only
Undetermined data error
I/O processor detected S/370 interface error
Device is not responding
Disconnect-In active on S/370 interface; I/O error alert
I/O processor detected Bus-in parity check
Device busy condition could not be cleared
Device address-in/system address-out; mismatch
S/370 interface time-out error
I/O configuration is not supported by this I/O processor
Device status; not permitted
I/O device detected word-count-0 error
I/O device detected even parity on bus-out
I/O device rejected command
I/O device detected overrun error
Tape I/O processor, Licensed Internal Code or card error
Tape I/O processor Licensed Internal Code
Vertical Licensed Internal Code
Bus terminating plug
S/370 Interface cable
External signal cable
Planar board
Tape I/O processor card
I/O device
Processor card
Tape
I/O device not communicating or continuously busy
Call your next level of support for assistance
Repair Guide; removal and installation procedures
Repair or exchange interface cable
Repair Guide; removal and installation procedures
Exchange Planar board
Repair Guide; removal and installation procedures
Refer to I/O device maintenance manual
Exchange card
Magnetic Tape Subsystem Operator's Manual
Tape I/O Processor diagnostic detected S/370 interface error
Tape configuration detected by system is not valid
Ensure that tape configuration valid for tape I/O processor
Load source DASD device
Alternate load source device (tape/optical)
Card enclosure
Tag terminating plug
Channel type is not supported on I/O Processor &26
The removable media device is assigned elsewhere
Channel type set incorrectly
Operator action required
User switched device type or model without IOP reset
Device switched on I/O processor &26 without reset.
Tape I/O Processor licensed internal code error.
AS/400 System Operator's Guide
I/O Processor or I/O adapter
I/O processor &26 had a licensed code error.
An input/output processor timeout has occurred.
Tape Control Unit Channel type not supported on this IOP.
Refer to the I/O device Maintenance manual
Threader assembly
Cartridge latch solenoid
File reel motor
Machine reel motor
Machine reel lower flange
Tape path sensor A
Tape path sensor B
Cartridge latch assembly
File protect switch
Cartridge present sensor
Tachometer sensor cable
Cartridge assembly
Message display assembly
Display cable
Write cable
Cartridge latched sensor
Decoupler assembly
Head guide assembly
Tension transducer
Plunger spring
Compression spring
Interlock spring
Fan assembly
Drive read card
Drive write card
Write bus terminator
Media IML disk
Loader mechanical assembly
Loader internal cable
Drive offline switch
CU operator panel
Drive control card
IML disk drive
DC power supply
Thermal switch
Buffer card
Latch interlock
Read detect card
Channel adapter cards
Control unit planar
Tape lifter solenoid input hose
Feed assembly
Output stack up-position sensor
Output stack assembly
Pneumatic parts
Drive reset switch
Drive address switch
Tape lifter solenoid
Machine reel tach sensor A
Machine reel tach sensor B
Loader control card
Load assembly
Stack low position sensor
Input stack assembly
Cartridge-in stack sensor
Cartridge staged sensor
Left input rail assembly
Stack up position sensor
Load motor complete sensor
Cable IML diskette drive
Pneumatic and fan control card
Message display board
Noise suppression network
An I/O Processor command timeout has occurred.
Air Moving Device 1 Fault
Air Moving Device 2 Fault
Air Moving Device 3 Fault
Air Moving Device 4 Fault
Air Moving Device 5 Fault
Air Moving Device 6 Fault
Air Moving Device 7 Fault
Air Moving Device 8 Fault
Air Moving Device 9 Fault
Air Moving Device 10 Fault
Power Supply P03 or P04 Overcurrent error
Power Supply P01 or P02 Overcurrent Fault
Power Supply P03 or P04 Overcurrent Fault
System Unit Interlock Failure
Secondary Frame Interlock Failure
Power Supply P01 or P02 Overcurrent error
CPM Signal Fault
CPM Regulator 1 Fault
CPM Regulator 2 Fault
CPM Regulator 3 Fault
CPM Regulator Load Fault
Power Good Type S error
Power Good Type M error
Power Good Type P error
Power Good Type I error
Power Good Type S Fault
Power Good Type M Fault
Power Good Type P Fault
Power Good Type I Fault
Air Moving Device Panel Fault
UPS Enable/Disable Failure
UPS CPM Failure
UPS Battery Failure
UPS Unit Failure
CPM Regulator PP1 Fault
CPM Regulator PP2 Fault
UPS Test Failure
UPS Interface Failure
Disk Unit regulator fault
Disk Unit regulator fault
Device regulator fault
Control Supply 5VSW power off failure
VPD 5V Power On Failure
VPD 5V Power Off Failure
Air Moving Device B01 Fault
Air Moving Device B02 Fault
Air Moving Device B03 Fault
Air Moving Device B04 Fault
Air Moving Device BP1 Fault
Air Moving Device BP2 Fault
Air Moving Device B01 Not Present
Air Moving Device B02 Not Present
Air Moving Device B03 Not Present
Air Moving Device B04 Not Present
Air Moving Device BP1 Not Present
Air Moving Device BP2 Not Present
Air Moving Device 0 Fault
Air Moving Device 3 Fault
Air Moving Device 4 Fault
Power Supply P01 not installed
Power Supply P01 ID is Invalid
Power Supply P02 ID is Invalid
Power Supply P03 ID is Invalid
Power Supply P04 ID is Invalid
Processor DCA-3 Seeprom VPD fault
Processor DCA-3 cable fault
Processor DCA-4 fault
Processor DCA-4 Seeprom VPD fault
Processor DCA-4 cable fault
Processor DCA-5 fault
Processor DCA-5 Seeprom VPD fault
Processor DCA-5 cable fault
Processor DCA-6 fault
Processor DCA-6 Seeprom VPD fault
Processor DCA-6 cable fault
Processor MDA-1 fault
Processor MDA-1 Seeprom VPD fault
Processor MDA-1 cable fault
Processor Fan 1 fault
Processor MDA-2 fault
Processor MDA-2 Seeprom VPD fault
Processor MDA-2 cable fault
Processor Fan 2 fault
Processor MDA-3 fault
Processor MDA-3 Seeprom VPD fault
Processor MDA-3 cable fault
Processor Fan 3 fault
Processor MDA-4 fault
Processor MDA-4 Seeprom VPD fault
Processor MDA-4 cable fault
Processor Fan 4 fault
BPC-A to BPC-B communication fault
Ambient room temperature limit exceeded
Capacitor card fault
BPC-A and -B are not at standby
UPS utility failure
UPS battery low condition was detected
UPS reported a bypass active
UPS utility power restored
UPS installed
UPS not available
UPS battery low condition was reset
UPS reported bypass no longer active
UPS failure
Battery Power Unit missing
Service processor failure caused machine check interrupt
Battery not working correctly
Service processor error to or from control panel
Interface error.
IPL1 failed in the service processor
Control panel self-test failed
Remote power-on failure
Service processor power-on failure
Manual power-on failure
Battery Backup Power Supply
Battery backup
Exchange
Control panel cable
Any storage unit
Failure of CEC power supply not identified by SPCN.
Service processor failure caused machine check interrupt.
SPCN - control panel interface error.
Control panel
Control panel battery
Power supply
Service Processor Card
Planar board
Cable assembly
Control panel keylock assembly
Power control cable
Service processor card real time clock failed
Repair and Parts; removal and installation procedures
Short circuit condition on one or more output voltage
Blower not operating at correct speed
Microprocessor in power supply failed
Power supply failed
AC voltage to power supply not in acceptable limits
AC voltage to power supply too low or absent a short time
Control signals from power supply failed
Programmable short circuit sensed on output voltage
One or more output voltage more than voltage limit
One or more output voltage less than voltage limit
Control signals from power supply failed
Card not seated correctly in card enclosure
Power supply failed
Power supply
Voltage too low on 24 volt supply in expansion unit.
Feature voltage error in expansion unit.
Current more than limit; 24 volt supply in expansion unit.
Logic regulator error in expansion unit.
Unit emergency power off in expansion unit
Voltage too high on 24 volt supply in expansion unit.
AC power error in expansion unit.
Expansion unit power failure
System unit power failure
EPO switch
Bus 0 extension adapter internal error
Main storage controller sensed not valid label or command
Main storage controller sensed internal error
Main storage controller sensed processor interface error
Main storage controller sensed address parity error
Main storage controller sensed wrong I/O address
Main storage controller sensed I/O address table error
Error in I/O address table in main storage during IPL
Data length error on processor interface
Main storage controller internal address parity error
Main storage controller sensed main storage data error
System processor card sensed machine check; cannot correct
Processor Licensed Internal Code sensed a card error
Bus 0 BEA sensed internal address or control error
Bus 0 extension adapter sensed address assigned after loaded
Bus 0 extension adapter sensed bus parity error
Bus 0 extension adapter sensed internal error
Service processor card sensed main storage controller error
Main storage controller; not valid command
Main storage slot 1 detected open during IPL
Licensed Internal Code or system processor error during IPL
Main storage slot 2 detected open during IPL
Main storage slot 3 detected open during IPL
Bus 0 extension adapter sensed system processor card error
Main storage sensed system processor error
Main storage slot 4 detected open during IPL
Main storage slot 5 detected open during IPL
Main storage slot 6 detected open during IPL
I/O System bus 0
Bus interface parity error
Licensed Internal Code error detected during IPL
Service processor card sensed internal error
Service processor card sensed I/O message count error
Internal error on service processor card
No main storage cards detected during IPL
System processor; Vital product data (VPD) read error
System processor sense Licensed Internal Code time-out error
Service processor card sensed main storage controller error
Bus interface data parity error
Service processor card cannot sense bus controller 0
Bus 0 extension adapter sensed not correct storage operation
Bus 0 BEA sensed internal address or label error
All main storage slots detected open during IPL
System bus isolation
Bus 0 extension adapter sensed data error; cannot correct
Bus 0 extension adapter sensed I/O message count error
Bus 0 extension adapter sensed MFIOP card error
Bus 1 extension adapter sensed address or label error
Bus 1 extension adapter sensed bus parity error
Bus 1 extension adapter sensed internal error
Bus 1 extension adapter sensed data error; cannot correct
Bus 1 extension adapter sensed I/O message count error
Cable test failure on bus 1
Bus 2 extension adapter sensed address or label error
Wrong main storage configuration detected
Bus time-out occurred
Bus extension adapter sensed internal address or label error
Bus extension adapter sensed bus parity error
Bus extension adapter sensed internal error
Bus extension adapter sensed data error; cannot correct
Bus extension adapter sensed I/O message count error
Incorrect instruction received from bus extension adapter
I/O bus 0
Bus 2 extension adapter sensed bus parity error
Bus 2 extension adapter sensed an internal error
Bus 2 extension adapter detected data error; cannot correct
Bus 2 extension adapter sensed an I/O message count error
System processor or main storage error
Cable test failure on Bus 2
Main storage card failure in slot 1
Main storage card failure in slot 2
Main storage card failure in slot 3
Main storage card failure in slot 4
Main storage card failure in slot 5
Main storage card failure in slot 6
System processor card failure
Service processor card failure
Bus 2 extension adapter card failure
Service processor card
System processor card or service processor card failure
Service processor card or system processor card failure
System processor card or bus 2 control card failure
Bus 2 extension adapter or system processor card failure
Service processor card or bus 2 control card failure
Bus 2 extension adapter card or MFIOP card failure
Bus adapter received bad horizontal code instruction
System processor card or main storage card slot 1 failure
System processor card or main storage card slot 2 failure
System processor card or main storage card slot 3 failure
System processor card or main storage card slot 4 failure
System processor card or main storage card slot 5 failure
System processor card or main storage card slot 6 failure
System processor, main storage, or system unit failure
Main storage card slot 1 or system processor card failure
Main storage card slot 2 or system processor card failure
Main storage card slot 3 or system processor card failure
Main storage card slot 4 or system processor card failure
Main storage card slot 5 or system processor card failure
Main storage card slot 6 or system processor card failure
Processor, service processor, or bus 2 control card failure
Service processor, processor, or bus 2 control card failure
Bus 2 BEA, System processor, or MFIOP card failure
System processor card failure sensed during IPL
Service processor card failure sensed during IPL
Bus 2 extension adapter card failure sensed during IPL
Main storage failure sensed during IPL
System unit failure sensed during IPL
System processor or service processor failure during IPL
System processor or system unit failure sensed
Control address table error sensed during IPL
Main storage error in slot 1 sensed during IPL
Main storage error in slot 2 sensed during IPL
Main storage error in slot 3 sensed during IPL
Main storage error in slot 4 sensed during IPL
Main storage error in slot 5 sensed during IPL
Main storage error in slot 6 sensed during IPL
Main storage or system unit failure sensed during IPL
Main storage slot 1 interface error sensed during IPL
Main storage slot 2 interface error sensed during IPL
Main storage slot 3 interface error sensed during IPL
Main storage slot 4 interface error sensed during IPL
Main storage slot 5 interface error sensed during IPL
Main storage slot 6 interface error sensed during IPL
System processor or system unit failure sensed during IPL
System processor or main storage slot 1 failure during IPL
System processor or main storage slot 2 failure during IPL
System processor or main storage slot 3 failure during IPL
System processor or main storage slot 4 failure during IPL
System processor or main storage slot 5 failure during IPL
System processor or main storage slot 6 failure during IPL
Main storage card in slot 0 not valid
Main storage card in slot 8 not valid
Main storage card in slot 9 not valid
Main storage card in slot 10 not valid
Main storage slots 3 and 4 interface error sensed during IPL
Main storage slots 2 and 5 interface error sensed during IPL
Main storage slots 1 and 6 interface error sensed during IPL
Main storage card in slot 1 not valid
Main storage card in slot 2 not valid
Main storage card in slot 3 not valid
Main storage card in slot 4 not valid
Main storage card in slot 5 not valid
Main storage card in slot 6 not valid
Main storage card not valid
Service processor Licensed Internal Code
Main storage card in slot 7 not valid
Licensed Internal Code sensed system processor card error
Main storage slot 7, system processor, or system unit
Processor card or horizontal Licensed Internal Code failure
System processor, main storage card slot 7, or system unit
System processor, main storage card slot 6, or system unit
Service processor card or system processor failure
Vertical Licensed Internal Code or system processor failure
Main storage card failure in slot 7
Main storage cards, system processor, or system unit
Vertical or horizontal Licensed Internal Code sensed
Main storage card slot 6, processor card or system unit
Main storage card in slot 11 not valid
Main storage card in slot 12 not valid
Main storage card in slot 13 not valid
Main storage card in slot 14 not valid
Main storage card in slot 15 not valid
Main storage card in slot 16 not valid
Main storage card failure in slot 11
Main storage card failure in slot 12
Main storage card failure in slot 13
Main storage card failure in slot 14
Main storage card failure in slot 15
Main storage card failure in slot 16
Licensed Internal Code or main storage error
Licensed Internal Code error or system processor failure
Main storage failure or Licensed Internal Code error
Main storage or Muliple function IOP failure
Main storage, Licensed Internal Code or muliple function IOP
Main storage, System processor or System bus adapter failed
Main storage, System processor or Multiple function IOP
Main storage, system processor or Licensed Internal Code
Multiple function IOP or Licensed Internal Code error
Multiple function IOP or Main storage failure
Multiple function IOP or System bus adapter failed
MFIOP, System bus adapter or System processor failed
MFIOP, System bus adapter or Main storage failure
MFIOP, System processor or System bus adapter failure
Multiple function IOP, System processor or Main storage
MFIOP, System processor, Bus adapter or Main storage failure
System bus adapter failed
System bus adapter or System processor failure
System bus adapter or Licensed Internal Code error
System bus adapter or Main storage failure
System bus adapter or Multiple function IOP failure
Bus adapter, multiple function IOP or Licensed Internal Code
Bus adapter, main storage or Licensed Internal Code error
Bus adapter, Multiple function IOP or System processor
Bus adapter, system processor or Licensed Internal Code
System bus adapter, System processor or Main storage
Bus adapter, System Processor or Multiple function IOP error
System processor failure or Licensed Internal Code error
System processor or System bus adapter failure
System processor, System bus adapter or MFIOP failed
System processor, Licensed Internal Code or bus adapter
System processor, Main storage or System bus adapter failure
System processor, MFIOP or System bus adapter failure
System processor diagnostic code
System processor, multiple function IOP or internal code
Unknown IOP, system processor or internal code failed
Licensed Internal Code error or system processor failure
Multiple function input output processor card
Failure detected on multiple function I/O processor card
Multiple function IOP or system processor failure
System processor or multiple function IOP failure
A system processor failure is detected.
A system processor failure is detected in slot 9.
A system processor failure is detected in slot 10.
A system processor error is detected.
System processor diagnostic code detected an error.
A system processor error is detected.
A system processor is missing.
A system processor diagnostic routine was bypassed during IPL.
Main storage expansion error
Main storage failure
Main storage, system processor, or system unit failure
Main storage error sensed in slot 8
Main storage error sensed in slot 7
Main storage error sensed in slot 6
Main storage cards or system unit failure
System processor card or main storage cards failure
No main storage cards detected
Licensed Internal Code error
System unit failure
Repair Guide; removal and installation procedures
Cache errors detected on system processor
Control store parity error detected on system processor
System bus adapter, System processor or MFIOP failure
Licensed Internal Code error or system bus adapter failure
Licensed Internal Code, bus adapter or bus extension adapter
Main storage failure or Licensed Internal Code error
System bus adapter or Bus extension adapter failure
Main storage error or System bus adapter failure
System bus adapter, Multifunction IOP or Main store failure
System processor card or system unit failure
Any card or adapter card
Main storage expansion
Service Functions; Working with Storage Dumps
Optical bus cable
Optical bus cable failure
Bottom or only main storage expansion card (half)
Top main storage expansion card (half)
Expansion unit bus attachment card
Expansion unit planar board
System processor card
Bus extension adapter card
Bus 2 extension adapter card
Any or all main storage card slots
Main storage card slot 1
Main storage card slot 2
Main storage card slot 3
Main Storage Card Slot 4
Main Storage Card Slot 5
Main Storage Card Slot 6
Horizontal Licensed Internal Code
System unit
I/O card unit
I/O processor
Main storage cards
Main storage card
Main storage expansion card
Repair and Parts; removal and installation procedures
Repair and Parts; removal and installation procedures
Main storage
Bus cable
Cables for bus 2
Bus expansion card
FC5021 card unit
Bus 2 adapter card
Repair Guide; removal and installation procedures
Attempting to power off the system
Bus controller problem detected during IPL
Not valid system configuration detected during IPL
Bus time-out occurred on bus 0
Tape problem detected during IPL
Service processor test completed
Main storage dump not allowed after IPL from tape
Problem detected on bus 0 during main storage dump
Valid main storage dump already exists on disk
Main storage dump advancing
Main storage dump completed
IPL device failed or not found
Error detected on storage device IOP on bus 0
Problem detected during IPL
Problem detected with bus controller for bus 0
Problem detected with service processor
Problem detected with control panel
Problem detected with control panel interface
Storage device IOP on bus 0 failed during IPL
Error detected on bus unit on bus 0
Problem detected with system processor
Problem detected with service processor card
Service processor Licensed Internal Code failed
Bus time-out occurred on bus 0 during IPL
Service processor test advancing
Service processor test failed
Normal service processor IPL advancing
Service processor failure during main storage dump
Service processor problem detected during IPL
Control passed to the system processor during IPL
Normal system IPL advancing
System IPL now starting
Tape IPL device failed or not found
Problem detected during programmed IPL
32 bus units on bus 0; more than limit of 31 bus units
Service processor lic int code load not found during IPL
Problem detected during main storage dump
IPL device not responding
System processor problem detected during IPL
Main storage dump already completed
No disk space available for main storage dump
Received error signal from I/O processor during IPL
Card detected in slot after primary bus extension card
Secondary bus extension card not in slot 0 of I/O card unit
System processor
Problem detected on bus 0 during IPL
Processor Licensed Internal Code load not found during IPL
Power off request received from control panel
Power off did not complete; starting main storage dump
System power will not power off; interrupted by test tool
Power off did not complete; starting problem determination
System will not power off; main storage dump in progress
Problem detected on bus 0 during system power off
Multiple function IOP communications to IPL device failed
Performing system memory tests during IPL
Waiting for IPL device respond
Communication connected to IPL device
IPL device problem detected during IPL
Multiple function IOP internal failure detected during IPL
System processor time-out during IPL
Wrong command received from IPL device during IPL
Command to IPL device failed during IPL
System processor reported system failure
No vital-product-data from system processor during IPL
Multiple function I/O processor internal failure detected
Starting vertical Licensed Internal Code initialization
Any device attached to Bus 1
Any device attached to Bus 1 or the Load Source IOP
Service Processor Problem Isolation Procedure
Problem with load source device media
Service processor completed hardware reset function
Service processor completed hardware error detection test
Service processor completed simple scan register shift test
Service processor testing storage scan register
Service processor completed self test register test
Service processor completed register test
Service processor set save area bits
Service processor set control panel parameters save area
Service processor loading MFIOP RAM code
Service processor not able to use timer services
Service processor timeout; hung in machine control task
Service processor function failed
Service processor received reset time-out from system proc
Service processor received error state notice but no error
Service processor LIC problem
Service processor detected private bus 0 parity error
System processor time-out before operational load complete
System processor time-out; HLIC initialization not complete
Service processor initialization complete; IPL starting
Service processor resetting MFIOP for main storage dump
Service processor completed reading processor error status
Service processor completed reset processor error condition
Completed transfer of bus control to service processor
Service processor completed performing processor diagnostics
Service processor completed checking restart processor IPL
Service processor internal software problem detected
Bus error occured on bus 0 during IPL
Service processor completed selecting critical error report
Service processor loading from MFIOP load-source defaults
Service processor ROS problem detected during IPL
Service processor starting to power off the system
Service processor hardware reset failed
MFIOP ROS testing tape device interface
Not able to complete initialization of service processor
Not able to set up service processor interrupt handler
Service processor vital product data hardware failed
Control panel not responding in required time limit
Service processor ran out of storage in MFIOP
Service processor function completed
Service processor loading MFIOP RAM code
Service processor not able to use timer services
Secondary bus extension
Primary bus extension
Processor card
Main storage cards
Service processor time out; hung in machine control task
Service processor function failed
Service processor received reset timeout from processor
Service processor is in incorrect state during IPL
Service processor hardware cannot determine system type
Main storage dump not allowed after alternate IPL
Service processor request rejected
Keylock is not in the correct mode.
System down, condition reported
MFIOP dump completed
Service processor resetting system processor
Service processor testing bus 0
Service processor initializing bus 0
Service processor checking for MFIOP load-source
Service processor loading from MFIOP load-source
Service processor loading from bus 0 IOP load-source
Service processor RAM code beginning
Service processor retrieving error data from IOP card
Service processor loading from bus 0 IOP defaults
System processor timeout problem on bus 0 during IPL
Fast Power Off requested, protection enacted
System processor interface problem dectected during IPL
System processor in error-state on bus 0 during IPL
Bus controller state problem detected during IPL
Problem detected with MFIOP
Bus 0 processor status register problem during IPL
Service processor RAM loading code using MFIOP load-source
Service processor RAM loading code using bus 0 load-source
Bus 0 load-source IOP configuration entry not found
Load-source disk device not found for MFIOP
Load-source tape device not found
Load-source tape device not ready for MFIOP
Service processor RAM code detected a problem during IPL
IOP on bus 0 could not be enabled
IOP bus time-out occurred on bus 0 during IPL
IOP on bus 0 failure indicated in the bus status
IOP on bus 0 failed to acknowledge a command
IOP on bus 0 sent an unexpected message
Message-wrap test of IOP on bus 0 returned wrong data
IOP on bus 0 returned less data than expected
Attempted a directed IPL from a non-load-source IOP
IOP on bus 0 rejected initial bus test command
IOP on bus 0 indicated; wrong data on IPL command
IOP on bus 0 detected bus controller DMA problem during IPL
IOP on bus 0 had data miscompare on DMA during IPL
IPL command rejected; bus 0 IOP already loaded
IPL command rejected; bus 0 IOP not loaded
IPL command rejected; wrong unit address for load-source
IPL command rejected; bus 1 load-source unit not ready
IPL command rejected; LID not found on load-source
IPL command rejected; bus 0 load-source IOP busy
IPL command rejected; wrong data to bus 0 load-source
IPL command rejected; load-source device failed or not found
Sending interface-reset-D to the load source IOP
Sending unit-reset-D to the load source IOP
Completed URD/IRD, waiting for bus command to continue.
Sending interface-reset to the load-source IOP
Sending initiate-self-load to the load-source IOP
Initiate-self-load completed by the load-source IOP
Load-source storage device controller completed IPL
Beginning system processor IPL
Sending message-wrap command to system processor
Message-wrap command completed by system processor
Service processor delivering system processor code
Sending query-IPL-data command to the load-source IOP
Query-IPL-data command completed from load-source IOP
Sending get-IPL-data command to the load-source IOP
Get-IPL-data command completed from load-source IOP
Sending load-from-storage command to the system processor
Load-from-storage command completed from system processor
Main storage dump completed; not enough disk space
Processor code load downloaded; waiting for HLIC request
First HLIC load delivered to system processor
Switching bus control to system processor
Switching bus control to service processor
Continue command sent to the system processor
Bus 0 initialization starting
Bus 0 initialization successful
Waiting for the load-source device to become ready
Waiting for a tape read command to complete
Waiting for a tape rewind command to complete
Waiting for a tape space command to complete
A tape read from the load-source completed successfully
Tape initialization completed successfully
Flush of system processor completed successfully
System processor configuration set successfully
Bus controller initialization completed successfully
Removed a system processor successfully
Added a system processor successfully
System processor interface tests completed successfully
System processor self-tests completed successfully
Service processor internal problem detected during IPL
Failure during transfer of bus control
Bus 0 failure while sending bus unit message
Load-source device on the MFIOP did not become ready
System processor code load not found on MFIOP load-source
MFIOP device interface failure
Media format wrong
System processor dump completed; not enough disk space
Main storage dump preparing to write to disk
Main storage dump completing status
Main storage dump reading processor 0 data
Main storage dump reading processor 1 data
Main storage dump initializing status area
Tape or CD storage unit failure
System processor configuration problem detected
Communication problem with system processor
System memory card configuration problem detected
System processor time-out problem on bus 0 during IPL.
Stuck-fault detected on bus 0 during IPL
System processor timeout problem on bus 0 during IPL
Load-source storage device controller on bus 0 failed
Load-source storage device controller is in error-state
Service processor code access failure during IPL
Service processor unable to reset system processor
Multiple function I/O processor (917A/917B/917C)
Service processor unable to start system processor
Service processor unable to stop system processor
IPL command to bus 0 load-source IOP failed
Multiple function I/O processor (9152/9153)
Apply PTF process for the control panel failed.
Bus controller problem detected during IPL
Card/bus expansion unit IOU(5021)
Service processor code initialization failure during IPL
Service processor unable to read system main storage data
Service processor code failure during IPL
Control panel (2648)
IPL command to system processor failed with bus 0 time-out
IPL command to system processor failed with bus-timeout
System processor failed to respond in time to an IPL command
System processor responded to command with undefined status
IMPI processor sent unexpected message to service processor
Switch bus control failure; system processor not ready
System processor in error state during IPL
Read immediate status to system processor failed
Bus 0 disabled due to bus-timeout during IPL
System processor returned status command; wrong subcommand
Message-wrap test of system processor returned wrong data
System processor detected bus controller DMA problem on IPL
Problem detected on bus 0 during main storage dump
System processor dump completed successfully
Bus time-out occurred on bus 0 during IPL
Reading machine check log buffer from main storage
Reading control address table from main storage
Main storage dump reading system processor data
Main storage dump wrote system processor data to disk
Main storage dump reading main storage data
Service processor LIC interface error during dump
Main storage dump called with request to retrieve no data
No processors configured when main storage dump was called
All processors failed during main storage dump
Dump not allowed after IPL from device not attached to MFIOP
Service processor ran out of storage; attempted MFIOP reset
Failure during transfer of bus control to service processor
System processor error detected during main storage dump
Service processor internal problem detected during dump
Service processor program task not responding during dump
Service processor not able to communicate with disk
Disk device not ready during main storage dump
Disk device failure reported during main storage dump
Service processor LIC problem during dump
Hardware error while reading main store data during dump
Main storage dump reading processor data
Service processor performing system diagnostics
Service processor reading system processor error status
Service processor resetting system processor error condition
Transfering bus control to perform processor diagnostics
Service processor performing processor diagnostics
Service processor checking for restart processor IPL
Service processor selecting critical processor error report
Service processor completing system diagnostics
Completed checking for restart processor IPL
Processor hardware failure; cannot retrieve processor error
Service processor LIC problem during diagnostic
Processor register not set valid when reading error status
Processor error status was reset by processor LIC
The control panel LIC update was successful.
Service processor detected an error.
Hardware failure.
System Power Control Network interface failure.
Control panel interface failure.
Hardware error during control panel communication; parity
Processor error status is zero during processor diagnostics
Stuck fault detected on bus 0 after bus timeout
System processor did not respond to bus 0 power off message
Performing control panel code update
Control panel LIC update failed; LIC load missing data
Control panel LIC update failed; LIC load not valid
Control panel LIC update failed; panel does not respond
Control panel LIC update failed; panel communication error
Control panel LIC update failed; panel code load not found
Control panel LIC update failed; switch to new code failed
Control panel LIC update failed; panel hardware error
System power control failures on retries
System power control rejected retries
System power control command not pending
Service processor time-of-day hardware failed
Service processor hardware parity error
Communication processor IOP(2623)
Service processor completed hardware error detection test
Control panel cable
I/O card adapter IOA(6018)
I/O card adapter IOA(6019)
Workstation IOP IOP(6140)
Multiple function I/O processor (2615)
Horizontal LIC initialization complete
Error status received from system processor
Request-load received from system processor
Operational load complete received from system processor
Reset-timeout request received from system processor
Bus message received from system processor is not valid
Bus message received from bus 0 IOP is not valid
Service processor diagnostics ended due to request
Service processor diagnostics not available
System processor in error state
Waiting for request load from system processor
Waiting for operational load complete from system processor
System processing unit stopped successfully
System processing unit started successfully
Stop or start system processing unit failed; bus 0 error
Stop or start system processing unit failed; no response
Stop or start system processing unit failed; parity error
Stop system processing unit failed; already stopped
Start system processing unit failed; LIC error
Start system processing unit failed; IPL not complete
Start system processing unit failed; processor stopped
Service processor IPL advancing
System processing unit stopped unexpectedly
Service processor stopped due to operating system request
Sending write-address-D to the load-source IOP.
Error in sending message to control panel; retry successful
Error in sending message to control panel; retry failed
Error in message from control panel; retry successful
Error in message from control panel; retry failed
Service processor recovered from a software error
MFIOP ROS testing MFIOP control storage
MFIOP ROS testing device interface
MFIOP ROS testing disk device interface
MFIOP RAM testing device interface
MFIOP ROS completed control panel interface test
MFIOP RAM testing service processor registers
MFIOP RAM testing time-of-day registers
MFIOP ROS completed service processor register test
MFIOP ROS completed set of save area bits
MFIOP ROS set control panel parameters save area
Main storage dump requested, protection enacted
Storage device IOP card failed
Storage device IOP communications to system failed
Storage device IOP statistics have been logged
Storage device IOP detected error on device cable
Storage device IOP communications to device failed
Storage device IOP detected error in device response
Storage device IOP sent data to wrong system address
Attached storage device stopped working
Storage device IOP Licensed Internal Code failed
Storage device IOP or Licensed Internal Code failed
Configuration not valid; too many devices attached
Storage device IOP and device communication error log
Command time-out occurred; reset sent to device
Open circuit was detected on device cable
Shorted circuit was detected on device cable
Write and Read test to the device failed
Error occurred in device starting sequence
Device format not set to 520 byte blocks
Device is down level or not supported
IOP Licensed Internal Code failed and recovered
Storage device IOP
Data Block was assigned to a new location on a disk unit
Configuration not valid, 6110 card has 9336 device attached
Configuration not valid, 6111 card has 9332 device attached
Configuration not valid, 6111 card has 9335 device attached
Device format error
A device replacement has occurred
Service Functions; APAR or LICTR
Magnetic storage device IOP card
Addressed storage device
Attached storage device
Storage device signal cables
Terminating plug
Magnetic storage device IOP Licensed Internal Code
Licensed Internal Code
Vertical Licensed Internal Code
Terminating plug
External signal cable
Planar board
I/O processor card
Base power supply
2440 Tape Unit
Device not addressed
System controller card
Tape, DASD or Optical Media
Call your next level of support for assistance
Magnetic Tape Subsystem Maintenance Manual
Repair Guide; removal and installation procedures
Exchange planar board
Repair Guide; removal and installation procedures
Check base power supply
Refer to device maintenance manual
Exchange field replacement unit
Inspect or exchange tape
I/O processor card Licensed Internal Code
Licensed Internal Code
9346 tape drive
Licensed Internal Code
Service processor Licensed Internal Code
Multiple function I/O processor Licensed Internal Code
9346 Tape Unit Service Guide, SY31-0688
Vertical Licensed Internal Code
Horizontal Licensed Internal Code
9346 IOP card
IPL device not ready
I/O command from tape not valid
Interface error not determined
Tape unit controller Licensed Internal Code
I/O processor card or Licensed Internal Code error
Service processor card or I/O processor card error
I/O processor card error
Addressed tape device failed to respond
Undetermined hardware error
Device status error occurred
Licensed Internal Code error
I/O processor card detected device error
I/O processor card, tape unit, or Licensed Int Code error
Repair and Parts; removal and installation procedures
Repair and Parts; removal and installation procedures
Storage device manual
Repair and Parts; parts listing
Storage subsystem configuration error
IOP timed out a disk command
Disk motor problem
Disk media format bad
9346 IOP card error; logged only
Disk sector read error
Temporary disk data error
9346 IOP card sensed busy response from tape unit
Temporary disk bus error
Tape drive, 9346 IOP card, or Licensed Internal Code
IOP card bus error
Service processor card or 2601 IOP card bus error
Tape unit configuration error
Tape unit does not support synchronous data transfer
Tape unit Licensed Internal Code error
Device not ready during IPL
I/O command from tape unit not valid
Tape too short
Removable media error during IPL
Searching configuration record, please wait
Tape unit or Licensed Internal Code error
Addressed tape device failed to respond
Attached tape unit not recognized or not valid
2440/9348 IOP card, tape unit, or LIC int error
2440/9348 IOP card error; logged only
2440/9348 busy response from tape unit
2440/9348 IOP card detected interface error
Recovered from condition in Licensed Internal Code.
Threshold overflow
I/O processor detected a buffer allocation error
I/O processor detected a random interrupt
I/O processor parity error
I/O processor detected a storage sequence error
System detected an I/O processor time-out
A permanent I/O processor failure occurred
Tape/CD or disk device failed to respond to selection
Tape/CD or disk bus interface error occurred
A tape/CD or disk device reported a failure
Storage unit detected a media problem
I/O processor detected a storage transfer error
I/O processor detected an internal error
I/O processor Licensed Internal Code error
Problem with removable media, possibly a user error
I/O processor detected a SCSI bus configuration error
Data compression failure, I/O processor operational
System bus error
I/O processor detected a timer problem
Read only storage failed, I/O processor is operational
I/O processor vital product data failed
The system vital product data has failed
Control storage failed, I/O processor is operational
I/O processor detected errors in control panel interface
Reset of the I/O processor header failed
I/O processor detected system clock and calendar failure
Disk or tape unit detected a recoverable error
Power Supply
Failure in initialization of a device task
Attached adapter card(s)
Operator/User Error
I/O processor detected a recoverable device error
I/O processor detected a storage device failure
Tape or disk unit busy during automatic test
Diskette automatic write/read wrap test failure
I/O processor cannot communicate with control panel
Adapter card storage failure
Adapter card storage or vital product data (VPD) failure
Type of adapter card not known
Type of tape/CD or disk unit not known
I/O processor was not ready for interrupt that occurred
Address error on I/O processor
Not valid instruction occurred on I/O processor
I/O processor detected a recoverable system bus error
Data decompression failure, I/O processor operational
EEPROM update occurred
System I/O bus error
I/O processor detected a recoverable SCSI bus error
Attached tape unit
Read or write error detected in storage area; recoverable
Adapter card not communicating to I/O processor
I/O processor memory error
I/O processor detected error in diskette control register
APPN session initiation attempt has timed out.
APPN session initiation attempt has failed.
APPN session timed out following device selection.
APPN session initiation attempt has timed out
APPN session initiation attempt has failed
APPN session timeout after device selection
Controller card detected a buffer assignment error
Controller card detected random interrupt
Communications IOP card parity error
Controller card detected storage sequence error
System detected communications card controller time-out
A permanent IOP card failure occurred
Communications controller card detected timer problem
Read-only storage failed, controller card is operational
Communications IOP card vital product data failed
Control store failed, IOP card is operational
Active adapter card
Adapter card not active
Communications adapter card
Active removable media or disk unit
Removable media or disk unit not active
Attached removable media or disk unit
Diskette unit
Active I/O processor
Processing unit
Feature card
Multiple function I/O processor card
Control panel
Terminating plug
Diskette adapter card
Defective removable media
Defective diskette
Licensed Internal Code
Cable assembly
Expansion unit planar board
Disk unit
Tape Unit
Power supply
Feature power supply
Power regulator card
Multiple interface adapter
Communications adapter card
I/O processor Licensed Internal Code
Test diskette (5-1/4 inch)
Test diskette (8 inch)
Twinaxial work station IOP
Communications IOP card
Token-ring network adapter
Licensed program
Disk drive and logic card
Disk drive logic card
Disk unit power regulator
Card Enclosure or Planar Board
Bus cable
Communication adapter
Tape unit IOP card
I/O processor card or attached cards, cables, or devices
Reset of the controller header failed
Controller card was not ready for interrupt
Address error on communications IOP card
Adapter card not communicating to IOP card
Communications controller card storage error
Control panel, or the interface to the Control panel
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
System Operations: Operator's Guide SC41-8082
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
Diskette read error
Diskette write error
Diskette unit control error
Drive error; wrong diskette type reported
Diskette controller card failure
Address changed
I/O signal cable error
Error during online problem analysis not expected
Diskette error data logged
Diskette volume statistics logged
Major error recovery performed; possible diskette failure
Part of diskette cannot be used; diskette still OK
Online problem analysis entered
Device error reported by storage device IOP card
Device is in service type operation
Diskette
Controller card
9331 diskette unit
Power supply
Diskette drive belt
Internal power cable
Control panel flexible cable
Fan assembly
Card-to-drive cable
9331 diskette unit test
Internal signal cable
Front cover
Address switch
Address changed
NONE
Repair Guide; removal and installation procedures
Service information binder insert
Setup manual, Address switch
Problem Analysis Guide; analyzing power problems
Out of alternate sectors for disk storage
I/O processor Licensed Internal Code error
Disk device returned wrong response to IOP
Disk or tape device detected recoverable error
*Attention* Impending DASD failure. Contact your hardware service provider now.
Disk device detected recoverable error
Diskette unit error
Diskette interface error occurred
Diskette controller detected program error
I/O card Licensed Internal Code error
Any adapter card attached to this IOP or INS.
I/O processor detected storage transfer error
I/O processor detected an operation status error
I/O processor resource not available
Not valid condition in I/O Processor Licensed Internal Code
IOP card or Licensed Internal Code error
IOP card or Licensed Internal Code error
Error reported to system
File protected
Physical end of tape
Door open
Tape reel missing
Tape reel inverted
No beginning-of-tape marker
Tape reel not correctly in place on supply hub
Address switch setting changed
Address switch failure
Tape path dirty or write data error
Tape unit ready status lost during read or write operation
Tape path dirty or gap noise error
Tape path dirty or write identification record error
Tape path dirty or write error
Tape path dirty or erase gap size error
Tape path dirty or read error
Tape path dirty or read error
Tape path dirty or more than one channel drop error
Tape path dirty or read identification record error
Tension arm voltage error
Tachometer error
Tape unit failure
Tape unit error reported by 2440 tape unit IOP
Volume statistics; logged only
Supply hub lock error
Take-up hub slip error
Tape or tachometer error
Logic board error
Logic board power-on test error
Supply motor power-on test error
Take-up motor power-on test error
Tachometer power-on test error
Tape path dirty or logic board error
Load failure; tape leader problem or static electricity
Tension arm moves too far
Supply hub slip
Tape speed error
Send or receive sequence error
I/O signal cable error
Send or receive synchronization error
Data not sent or not received successfully
Data overrun error
Error during online problem analysis not expected
I/O error; no reference code
Device in service type operation
Device found error while running test
Device error reported by storage subsystem IOP
Tape
1/4-inch tape unit
Tape unit not communicating; operator action needed
External signal cable
Unit-to-unit signal cable
2602 controller card
BUS/TAG terminating plug
9348 Customer Information
Exchange cable
Exchange card
Exchange terminating plug
Tape path dirty or write data error
Tape path dirty or write identification record error
Tape path dirty or more than one channel drop error
Tape path dirty or read identification record error
Tape unit failure
Tape unit ready status lost during read or write operation
Tape unit error detected by tape unit controller
Volume statistics; logged only
9348 Service Information
Write-enable sensor
Start of tape or end of tape sensor
Tape-in-path kit
Tape logic board
Control panel
Tachometer
Read and write head
Supply motor
Take-up motor
Interface cable
Transformer
Power supply
Tape supply hub lock kit
Tension arm kit
Front door lock
Power supply enclosure
Top cover lock
Tape or tape path
Tape
Tape unit
Tape unit not communicating
2440 Magnetic Tape Subsystem Operator's Manual, G571-0149
Small-computer-system-interface (SCSI) card in tape unit
2440 Magnetic Tape Subsystem Service Guide, G571-0166
Cooling fan
Front cover assembly
Control panel assembly
Read and write card
Planar board
Controller card
Data buffer card
Power/motor drive card
SCSI differential interface card
Tape sensor assembly
Start of tape or end of tape (BOT/EOT)
Speed sensor
Read and write head
Hub lock
Buffer arm
Tape lifter
Speed sensor cable
Front panel cable
Motor control cable
Cable harness
Interface cable
Read cable
Write cable
Reel motor
Cooling fan
Take-up hub
Supply hub
SCSI single ended interface card
Solenoid lock assembly
Error code not recognized; enter error code again
The tape is rewinding.
Tape unit ready with no tape loaded; press Enter
The tape unit is ready at the start of tape.
Tape unit idle and not at start or end of tape
The tape unit is waiting at or beyond the end of tape.
The tape is loading.
The tape is unloading.
The tape unit is reading from tape.
Repair Guide and Parts Listing; parts listing
The tape unit is writing to tape.
Tape unit is completing operations after being taken offline
The tape unit is waiting (system busy).
Tape unit is online; requested operation cannot be performed
Tape unit front panel pushbutton not permitted at this time
The system has disabled tape removal.
Too many read and write errors. Clean the tape path.
Tape unit power-on self-test detected a failure; press Enter
Operator Guide; cleaning procedures
Cannot find a resource name associated with the device name.
The tape unit is cancelling an operation.
Tape subsystem failure
Tape unit failure during write operation
Tape unit failure during read operation
Attempt to load tape failed
Start of tape is missing
Tape reel is inverted
Tape unit top cover or front door is open
Operator error
System lic int code problem occurred during tape operation
Tape unit not able to maintain streaming operation
Tape unit does not detect tape reel on the supply hub
Hub lock failure
Reel not seated on supply hub
Reel inverted on supply hub.
Tape load failure
The front door or top cover is open.
No beginning-of-tape marker was found on the tape
Tape failure
Problem Analysis Guide
Operating system Licensed Internal Code
Tape 10 feet beyond end-of-tape marker
Call your next level of support for assistance
EPROM kit
Door micro switch
2440 Service Guide or 9348 Service Information
Connector card
I/O processor card error; logged only
I/O processor card detected interface error
1/4-inch tape unit failed
Arrangement of data fields or record sequences not correct
9346 Controller (2601) addressed tape unit; no response
Tape Unit response not correct or 9346 Controller failed
Tape volume statistics logged (no action required)
Tape unit detected a read or write error on tape medium
Failure at system bus interface to 9346 Controller (2601)
9346 Controller card (2601) failed
Interface error; 9346 Controller (2601) to tape unit
9346 Controller card (2601) Licensed Internal Code failed
Damaged cartridge detected or the tape unit failed
Defective tape or damaged cartridge
9346 Service Guide; Installation and Removal, SY31-0688
System main processor card
Other card, cable, or connector on the same system bus
9346 Customer Information; Operating Guide, SA21-9542
9406 Unit Reference Code Guide, appendix FInnnnn Failing
9346 Controller card (2601)
Power cord; U.S.A., Asia-Pacific group, Americas group
Power cord; Europe, Mid-East, Asia
External signal cable
Internal signal cable
Internal tape unit signal cable
Internal power cable
Flex cable
Terminating plug
Power supply
Fan
Front cover
Wrong tape
Tape
Tape drive
Vertical Licensed Internal Code
Licensed program on 9346 Controller card (2601)
Base power supply
Repair Guide; removal and installation procedures
Repair and Parts; removal and installation procedures
Repair Guide; removal and installation procedures
2615 I/O Processor Card
2615 Tape MICROCODE
Repair Guide; removal and installation procedures
AC Module
DC Bulk Module
D/SE Module
Cable Carrier
Device Tray
Device Tray Adjacent to reported device tray
2621 I/O Processor Card
2621 Tape Microcode
Licensed Internal Code for 1/4-inch tape unit
The data format is incorrect; the tape cannot be read
2615 IOP card addressed 1/4" tape unit ; no response
Incorrect operation sent or received
Failed 2615 IOP card to 1/4" tape unit interface
Cartridge removed; end-of-tape processing did not complete
Cartridge changed or device reset; processing not complete
Device powered off; end-of-tape processing not complete
A recoverable interface error occurred
A recoverable not operational error occurred
IOP card addressed 1/4-inch tape unit; no response
Interface failure between IOP and 1/4-inch tape unit
Unexpected blank tape detected
Unexpected end-of-media detected
IOP detected incorrect response from the tape unit.
Tape unit detected incorrect request from the IOP.
Tape unit detected incorrect request from Vertical LIC.
Tape is not readable (written incorrectly)
Tape unit detected a write command with incorrect format.
Licensed Internal Code for the tape unit is not correct
Licensed Internal Code for tape unit was not upgraded
Tape unit failed after Licensed Internal Code was loaded
Licensed Internal Code for programmable tape unit
FI00870; Repair Guide; removal and installation procedures
1/4-inch tape unit; see FI00870 to determine type number
Device error has occurred
Tape format error occurred
Hard bus interface error occurred
Hard controller error occurred
Addressed device failed to respond to selection
Not defined sense key returned from target device
Tape or disk parity error occurred; cannot recover
Tape subsystem detected program error
Volume Statistics reported to the system
Device or tape status error occurred
IOP detected error
Read command counter overflow
Write-with-verify-counter overflow
A not valid command received when in limited function mode
Licensed Internal Code does not match the hardware
File processor detected error
Read error, data should be in another disk area
Read error, data should be in another disk area
Read error, data should be in another disk area
File processor detected error
Read error, data should be in another disk area
Read error, data should be in another disk area
Read error, data should be in another disk area
Servo processor detected error
Servo processor detected error
I/O error between 9332 and host
Driver and receiver card
I/O adapter card
Servo card 1
Servo card 2
Driver board
Driver board
Power supply
Disk enclosure
Disk enclosure
Fans
Address switch
Signal cable
Power cord
LED assembly
Licensed Internal Code
Device Service Documentation
None (not applicable)
Reference Code returned by 9335 diagnostic
Reference Code generated by User Guide or Service Guide
Equipment check detected by 9335 sub-system
Data check detected by 9335 subsystem
See 9335 User Guide or Service Guide
9335 error recovered by 9335 subsystem IML
Interface error
Error detected by 9335 subsystem
9335 Model B in service (CE) mode
Device error, position 1
Bus parity error, device 1
Communications failure, device 1
Disk drive initialize required
Disk drive is powered off
Additional disk drive required
Command issued to disk drive not supported
Disk drive installed not supported
Disk drive capacity does not match others in the array
Device error, position 2
Bus parity error, device 2
Communications failure, device 2
Device error, position 3
Bus parity error, device 3
Communications failure, device 3
Device error, position 4
Bus parity error, device 4
Communications failure, device 4
Device error, position 5
Bus parity error, device 5
Communications failure, device 5
Device error, position 6
Bus parity error, device 6
Communications failure, device 6
Device error, position 7
Bus parity error, device 7
Communications failure, device 7
Device error, position 8
Bus parity error, device 8
Communications failure, device 8
The spare drive under controller &27 requires service.
Communications failure with SPCN, call for hardware service
9337 failed switch on power, go to 9337 Service Information
9337 failed switch on power, call for hardware service
Internal command stopped, go to 9337 Service Information
Internal command stopped, call for hardware service
Configuration error, call for hardware service
Licensed Internal Code load required, call for service
Data error, sector reassignment required, call for service
LRC error, call for hardware service
Controller card failed, Write Assist Cache contains no data
Controller card failed, Write Assist Cache contains data
Controller card and Solid State Write Cache failed
New Solid State Write Cache, possible data loss
Solid State Write Cache failed, no data loss
Solid State Write Cache failed, data has been lost
Incorrect Write Cache size installed
Current more than limit, 5-volt supply
Current more than limit, -5-volt supply
Current more than limit, 12-volt supply
Fan sense logic failure
Fan 1 failure
Fan 2 failure
Operator panel assembly failure
IOP card, Licensed Internal Code stopped
Communication error, Write Assist Cache contains data
Power failure; PAR ending URC
AC power failure; PAR ending URC
Current more than limit, 5-volt supply; PAR ending URC
Current more than limit, 12-volt supply; PAR ending URC
IOP card failure; PAR ending URC
Licensed Internal Code detected error
Address switch changed since unit was powered on
Thermal error
Data error, sector reassignment required
Data error during sector reassignment
Disk unit,load Licensed Internal Code
Disk drive, load Licensed Internal Code
Data display contents not recognized
Customer engineer directed to system problem analysis
Customer engineer directed to disk unit analyzing problems
Customer engineer directed to run system recovery
User corrected the problem
User corrected the problem, fix is verified
Current more than limit, -5-volt supply; PAR ending URC
Communication failure with System Power Control Network
Disk unit offline
Recovery threshold exceeded on device under controller &27
Predictive Failure Analysis threshold reached
Disk drive has incorrect capacity
LRC error
Disk drive missing from disk array internal configuration
A disk drive was improperly substituted in the disk array
Data miscompare error
Configuration error, minimum configuration assumed
RAID protection suspended on controller &27
Power protection suspended on controller &27
Hardware error on device under controller &27
Configuration error on device &25
Information only, no service action required
Special device parity protection recovery required
Spare drive requires service
Device parity protection suspended on device &30, data is being built again on a spare device
AC power failure, user ran problem analysis; PAR ending URC
Address Switch changed, user ran problem analysis
Thermal error, user ran problem analysis; PAR ending URC
Data display contents B000, PAR ending URC
System log entry only, no service action required
Call for hardware service
Write/read buffer failure due to an interface error
IO processor can not degate disk unit from interface
Disk unit internal interface cable failure
Slave operational to not operational transition
Sequence error, unit interface
Parity error, disk unit interface
Sync in is not equal to sync out, disk unit interface
Master transfer not sucessful, disk unit interface
Error reported in slave status without a URC
Unit request to log information, no related URC for request
Communications failure with IOP, call for hardware service
Communications failure with IOP
Power subsystem failure, call for hardware service
9337 Service Information, Service Procedures, chapter 4
Service procedures, section 4
Disk drive assembly
AC Power cable filter
+5 volt overcurrent on a single power module
+12 volt overcurrent on a single power module
A single power envelope has failed in a power module
A single power module failed
Communications failure with a single power module
Communications failure with all power modules
Extra disk drives are installed in the disk array
Power module A
Power module B
Power module C
Disk array internal configuration error
Start change protection record from the system is missing
Data error, sector rewrite required
Connector panel
Operator panel assembly
Disk drive interface cable
Disk drive power cable
AC power cable
Disk drive logic card and disk enclosure
Disk unit Licensed Internal Code
Disk drive Licensed Internal Code
Disk drive type is not recognized, FRU part number unknown
Licensed Internal Code load needed, go to 9337 service guide
Threshold exceeded, controller replacement required
Data was not recovered, data must be written again.
(B) Servo 0 card
(B) Servo 0 card, unit 0
(B) Servo 0 card, unit 1
(B) Servo 0 card, unit 2
(B) Servo 0 card, unit 3
(B) Servo 1 card
(B) Servo 1 card, unit 0
(B) Servo 1 card, unit 1
(B) Servo 1 card, unit 2
(B) Servo 1 card, unit 3
(B) Servo cards 01A-A1B1,B5
(B) Failing item; motor driver
(B) Failing item; motor driver
(B) Disk enclosure
(B) Actuator Driver 0 Card
(B) Actuator Driver 1 Card
(B) Actuator driver cards 01A-G1A1,A2
(B) Demodulator 0 card
(B) Demodulator 1 card
(B) Demodulator cards 01A-A1A5,A1
(B) Motor
(B) Device interface card
(B) Device interface card, unit 0
(B) Device interface card, unit 1
(B) Device interface card, unit 2
(B) Device interface card, unit 3
(B) Read-detect 0 card
(B) Read-detect 1 card
(B) Read-detect cards 01A-F1A1,A2
(B) Motor lock assembly
(B) Interposers 01A-A1B1-W, 01A-A1B1-W
(B) Cross-card connector
(B) Actuator driver cables 01A-G1A1,A2
(B) Read-detect cables 01A-F1A1,A2
(B) Power control card
(B) Logic board
(B) Control panel
(B) Power switch
(B) Fan
(B) AC power box
(B) Circuit breaker
(B) Circuit breaker
(B) Circuit breaker
(B) Switch-mode power supply
(B) Power regulator card
(B) Transformer
(B) Transformer
(B) Power-thermal-trip switch
(B) Device interface cable
(A) SA1 System tailgate cable
Cable 3.50M (6.0M)
(B) Internal AC cable assembly
(B) DC cable assembly
(A) Internal AC cable assembly
Power compartment
(A) DC cable assembly
(B) Power regulator cable
(A) Device interface card
(A) Device read/write card
(A) System adapter card
(A) Control panel
(A) Cooling fan
(A) Power switch
(A) Power box
Power sequence cable, unit to rack
(A) Thermal trip-switch
(A) Device cables to units
(A) Device cables to units
(A) Board 01A
(B) Interposers 01A-A1B5-X 01A-A1B1-X
(B) Actuator driver logic cable
(B) Actuator driver card
(B) Sermod 0 card
(B) Sermod 0 card unit 0
(B) Sermod 0 card unit 1
(B) Sermod 0 card unit 2
(B) Sermod 0 card unit 3
(B) Sermod 1 card
(B) Sermod 1 card unit 0
(B) Sermod 1 card Unit 1
(B) Sermod 1 card unit 2
(B) Sermod 1 card unit 3
(B) Sermod cards 01A-A1B5, 01A-A1B1
9309 Service Guide
9309 Setup and Operator Guide
9335 Service Guide
User action required; Lic Int Code install/restore utility
Machine termination problem
Licensed Internal Code install/restore utility ended
Disk device problem
IOP problem
Not enough system storage for initial program load
Operating system failed
Operating system status code
Rack power problem
Service program failed
Licensed Internal Code install/restore utility status code
Licensed Internal Code install/restore utility problem
System equipment problem
Operating system recovery needed
Remote power-on problem
System licensed program or equipment failed
Operator selected the cancel option
Processor cannot communicate with the bus extension unit.
Expansion unit power cable problem
IOP reset problem
VLIC program failed and data was captured
VLIC program reported informational error
Operating system licensed program failed
System LIC program exception occurred
Service Functions; Lic Int Code install/restore
Set Up Guide
Program repair order
Repair Guide; removal and installation procedures
Call your next level of support for assistance
Problem Analysis Guide; I/O bus problem isolation procedure
IOP problem
IOP returned bad status on bus command
IOP failed internal tests
IOP sent bad status on bus command
IOP not successfully loaded
IOP timed out on I/O bus
IOP sent bus command out of sequence
IOP failed to assign bus unit address
IOP doesn't match internal tables
IOP sent invalid bus command
Tag line on I/O bus stuck active
Bus extender detected I/O bus failure
Bus idle timeout threshold count exceeded
I/O bus configuration error
Empty Bus Encountered During IPL
IOP Reset was issued
Optical bus link initialization failed
Optical bus is not cabled correctly
Wrong number of buses found because of optical link failure
Optical signal loss was detected
Optical bus failed
Optical link on Bus Expansion Adapter card failed
Bus Expansion Adapter failed
Optical link on Bus Expansion Adapter card failed
Bus Expansion Adapter card failed
Wrap plug is installed on Bus Expansion Adapter card
Bus Expansion Adapter card is not powered
All IOPs failed because of optical bus failure
Bus Expansion Adapter card
Bus Expansion Adapter card
Optical bus cable
Problem Analysis Manual
Optical wrap plug, bus X
Optical wrap plug, bus Y
Cable test failure
Storage I/O processor card
Workstation I/O processor card
Communication I/O processor card
Please type 9402, 9404, or 9046 and press Enter.
Informational bus reference code
Bus hardware configuration problem
I/O processor failure
Missing or failed I/O processor cards
System bus extension hardware detected a bus failure
A failure occurred on another system
Any system bus hardware
No I/O processors were found on the bus
A specific I/O processor
Two I/O processors at consecutive addresses are missing
Bus extension driver in wrong card slot
The even primary optical bus cable of a bus pair
Any primary optical cable
Secondary optical cable
Any optical cable or a missing wrap plug
Local bus adapter or system processor
Local optical link card
Remote bus adapter on this bus
Remote bus adapter on the paired bus
Non-BCU bus adapter card
Failure on another system
Power problem in a secondary rack or tower
Uninterruptible Power System reported a utility failure
Uninterruptible Power System reported power restored
UPS reported a battery low condition
Uninterruptible Power System reported a bypass active
UPS battery low condition turned off
UPS reported bypass no longer active
Operator response required
Configuration error
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Any IOP, I/O adapter or related bus equipment
IPL tape subsystem
Primary disk unit
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
IOP card
Main storage error; unknown slot
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
Vertical Licensed Internal Code
5763SS1 Licensed Internal Code
Vertical Licensed Internal Code
Card enclosure
Equipment failure; not isolated
Console device
Vertical Licensed Internal Code
Service processor card or multiple function IOP
Magnetic storage device IOP Licensed Internal Code
Power control cable
Blower
Air filter
AC box
Interposer card
Power sense cable
Vertical Licensed Internal Code
Option selected not valid
WS IOP detected error when transmitting data
WS IOP detected parity error from device
Device detected parity error from WS IOP
WS IOP detected device power turned off, and then on
WS IOP detected wrong data from device
WS IOP detected wrong address from device
Device detected wrong command or device ID from WS IOP
Device detected storage or data overrun
Device detected wrong start command from WS IOP
WS IOP detected wrong exception response from device
WS IOA detected parity error from WS IOP
WS IOA buffer utilization threshold exceeded temporarily
WS IOA performance statistics were not returned
WS IOP detected wrong request or response from device
WS IOP detected wrong device type from device
WS IOP detected no status change from device
WS IOP detected busy time-out from device
WS IOP detected wrong device response to start command
WS IOP detected wrong keyboard scan code from display
Device detected not valid value from WS IOP
Device detected null or attribute exception error
WS IOP detected not valid pass-through command
WS IOP detected wrong display size value
WS IOP detected wrong keyboard identification
WS IOP detected wrong status response from display
Printer detected equipment error
WS IOP detected start command to printer was lost
Too many devices active on the workstation IOP
Work Station IOA start-up test error
WS IOP storage failure corrected
WS IOP card storage failure
WS IOP detected errors on all cables
WS IOP parity errors detected on all cables
WS IOP detected errors on some, but not all cables
WS IOP or IOA error during working operation
WS IOP or IOA operating system program error
User-detected workstation problem
WS IOP error not known
Wrong magnetic stripe reader response
Wrong magnetic stripe reader or light pen status
Device no response time-out; temporary error
WS IOP fails to report part, model and serial number
WS IOP detected error downloading printer definition table
WS IOP detected error unloading printer definition table
WS IOP detected device configuration error
WS IOP detected error downloading LIC to device
Printer detected end of ribbon check
Work station I/O processor card
Work station attachment
Link protocol converter
Cabling
Work station
5299 Model 3 Terminal Multiple Connector
Twinaxial to twisted pair adapter cable
Electrical interference
Other work station on port is failing
Work station I/O adapter card
Communications I/O processor card
I/O adapter Licensed Internal Code
Error occurred with pass-through command
Printer
Too many work stations are active on the workstation IOP
Work Station IOP or IOA system Licensed Internal Code
Display
Active device turned off
Magnetic stripe reader
Selector light pen
Magnetic stripe
Twinaxial cables
IBM Cables System
Telephone twisted pair cables
5259 Migration Data link
User believes there is a problem
Work station attachment conversion cable
FIRST WORKSTATION ATTACHMENT PLATE - TWINAXIAL
FIRST WORKSTATION ATTACHMENT PLATE CABLE
FIRST WORKSTATION ATTACHMENT KEYBOARD EXTENSION CABLE
FIRST WORKSTATION ATTACHMENT DISPLAY - TWINAXIAL
FIRST WORKSTATION ATTACHMENT KEYBOARD - TWINAXIAL
Printer definition table
POWER SUPPLY
Data Stream error caused by the system application
Printer detected a data stream error
Device Licensed Internal Code change
Remote Controller
Remote Controller or System Configuration
System Code
Repair Guide; removal and installation procedures
Repair Guide; removal and installation procedures
Protocol Converter Service Manual
Cable service manual
Device Service Manual
IBM 5299 Model 3 Guide; GA27-3749
IBM 5250 Information Display System Guide; GA21-9337
Printer service manual
IBM Cabling System Documents - GA21-9491 and GA27-3620
Workstation service manual
Migration data link service manual
Communications error; data-set-ready line not active
Communications error; received line was idle
Communications error; receive-clock signal failed
Communications error; data-set-ready line failed
Communications error; 30-second time-out occurred
Communications error; data set will not activate
Communications error; frame reject was received
Communications error; disconnect received while not ready
Communications error; clear to send error
X.25 communication error
X.25 communication error; IOP has ended the link
X.21 communication error
Communications error; command reject was sent
Communication error; X.21 adapter card error
SDLC test frames with error or X.25 receive-not-ready
SDLC test frames without error or X.25 receive-not-ready
Counter; communications adapter underrun
Counter; Communications adapter overrun
Counter; loss of receive-line signal-detect signal
Counter; loss of clear-to-send signal
Counter; loss of data-set-ready signal
Counter; frame sequence error
Counter; transmit retry
Counter; frames received with cyclic redundancy check (CRC)
Counter; frame abnormally ended
Counter; X.21 adapter card errors
Counter; timer 1 time-outs
Counter; transmitted information frames
Counter; valid information frames received
Graphic check occurred on printer
SNA character-stream command was not valid
SNA character-stream parameter was not valid
End of forms on printer
Printer not ready
Reset command was sent to printer
Shared printer was busy
Communications error; transmit-clock signal failed
Communications error; internal IOP failure
Communications error; timer 1 retry count reached
Intermediate protocol data unit (IPDU) transmitted again
Work station IOP card and 12 port attachment
Device; display, printer or modem
ASCII work station IOP card
6 port ASCII workstation attachment
12-port ASCII work station attachment
ASCII modem cable
More than 18 attempts to vary on device; limit 18
Communications line
ASCII modems
Device cable
Electrical interference
ASCII work station IOP system Licensed Internal Code
Repair Guide; removal and installation procedures
ASCII Work Station Reference, SA41-9922
Modem service manual
Workstation IOP detected parity error from display
Workstation IOP detected overrun error
Workstation IOP detected framing error from display
Workstation IOP detected wrong scan code
WS IOP detected operating system error; device ID
WS IOP detected operating system error; register value
Workstation IOP detected storage overrun
WS IOP detected null or attribute exception error
Workstation IOP detected not valid exception status
WS IOP detected operating system error; bad device type
WS IOP detected busy time-out error from display
Workstation IOP detected parity error from printer
Workstation IOP detected overrun error
Workstation IOP detected framing error from printer
WS IOP detected system program error; device identification
Workstation IOP detected not valid exception status
WS IOP detected busy time-out error from printer
WS IOP detected more than 18 devices varied on; limit 18
WS IOP detected device configuration mismatch
WS IOP asynchronous port errors on all ports
WS IOP asynchronous port errors on some ports
WS IOP asynchronous errors on all ports
WS IOP asynchronous port errors on 12 port attachment only
WS IOP asynchronous errors on some ports
Configuration
Repair Guide; removal and installation procedures
ASCII Workstation Attachment Assembly
Device still active on the port
Diagnostic wrap test completed; error was detected
Diagnostic wrap test completed; no errors detected
Diagnostic wrap test ended abnormally
WS IOP detected a transmit complete time-out
No response received from workstation; idle time-out
Data sent by WSC not received by workstation
Data sent by workstation not received by WSC
Workstation IOP detected a frame error
WS IOP received a frame reject command from workstation
WS IOP received unexpected data from workstation
WS IOP DMA receive buffer overrun; SDLC data
WS IOP DMA receive buffer overrun; not valid data
WS IOP frame buffer overrun of valid data
WS IOP DMA receive buffer overrun; not valid data
Workstation IOP detected Xoff-Xon time-out
Start-up failure
Work station adapter card
Programmed workstation with PC Support installed
Hardware Maintenance and Service manual
User believe there is a problem
ASCII WORKSTATION EXPANSION PLATE
ASCII WORKSTATION I/O PROCESSOR and WORKSTATION PLATE
WS IOP failed automatic line speed detection
WS IOP failed automatic device type detection
Not able to allocate device description
Input/Output station is empty
Input/Output station already contains cartridge
Optical library is full, cannot accept cartridge
Slot selected not valid
Optical library request timed out
CE test cartridge is write-protected
Cartridge received is not CE test cartridge
Optical library internal DASD must be initialized
CE test cartridge not found in optical library
URC Information not available
Object authority not granted
Not able to locate optical device description
Option selected not supported
Not able to obtain optical configuration lock
Optical library configuration not complete or not valid
Unexpected error occurred
Cartridge received is not blank
*SERVICE authority required for DASD initialization
Required system translate table not found
Optical library support not started
Optical drive selected is not valid
Required support not installed or not started
*JOBCTL authority required for problem analysis
CE Test Cartridge successfully initialized
Data read does not match data written on optical disk
Not able to locate next blank sector on CE Test Cartridge
No optical drives reported by IOP
More information available - press Enter
Not able to reach needed device status
Optical media not compatible with optical drive
Optical media error occurred
Optical library device error occurred
An optical media or device error occurred
Optical volume not found
Optical volumes not properly matched
Duplicate optical volume found in library
Optical library IOP reset not complete
Optical library IOP error occurred
Optical library internal DASD error occurred
Serial number is a duplicate value
Serial number may not be all zeroes
Serial number contains characters that are not valid
Optical library picker did not become operational
Optical library did not vary on
Optical library did not become active
Device type and model could not be determined
Complete device information was not available
Internal DASD reported as failed by IOP
Picker arm reported as failed by IOP
Optical drive reported as failed by IOP
Cumulative statistics last reset date not available
Optical library operation in progress, please wait
Waiting for lock on optical configuration
Choice not supported at this time. Choose another type/model
System unit power supply
Expansion unit power supply
Card or device in System unit
Card or device in Expansion unit
Chassis
Control panel failure
Tape unit does not support synchronous data transfer
SCSI MPU card
Capstan wheel
2440 Magnetic Tape Subsytem Service Guide
Tape device reset in progress, please wait.
PLO Card
Defective tape or diskette
Library device
IBM 3494 Maintenance Information, SA37-0270
A command could not complete in MLB &37 on device &39 because a library path check occurred.
Library device failure
Maintenance Information and Parts Listing, SA37-0296
SCSI adaptor card
A command could not complete in MLB &37 because of a library manager incompatibility.
MLB &37 vision system is nonoperational
A library manager equipment check has occurred in MLB &37
MLB &37 is in pause mode because of a library equipment check.
MLB &37 device &39 device failure.
MLB &37 requires operator intervention.
MLB &37 volume &38 is inaccessible.
A Media Library Device Driver error occurred.
Media Library Device Driver
Library device requires operator intervention
Media Library Device Driver error
An command could not complete in MLB &37 because the library vision system is nonoperational
MLB &37 An environmental alert has been detected within the media library device enclosure
Library enclosure environmental alert was detected.
Licensed Internal Code for resource &28 was not upgraded.
I/O processor card detected media error
Defective media
3490 Control Unit Licensed Internal Code
3494 Library Manager Licensed Internal Code
External Diskette Unit Service Manual
Internal Cable Assembly
Power Supply Assembly
LED/Switch cable assembly
Power Switch Assembly
Physical Transfer Error
Missing card
Misplugged card
Communications input/output processor card
System input/output Bus or any attached card
Communications adapter card
Workstation input/output processor card
Communications adapter card failed or missing
Communications input/output processor card failed or missing
Workstation input/output processor card failed or missing
I/O Processor card failed or missing
I/O processor card
Tape with excessive error rate was mounted in tape device.
Device Licensed Internal Code failure
Tape device failure, redundancy lost
Tape device failure or media error
Problem analysis has determined a part should be replaced.
Problem analysis completed, the problem has been corrected.
Fibre Channel interface error detected
Equipment Check Failure on Library Device.
Gateway device detected a bus protocol error
Gateway device failure
Gateway device Licensed Internal Code error
Gateway device detected a SCSI interface error
Tape performance statistics logged.
Hardware encryption error.
Tape device information logged.
Hardware configuration change detected.
Tape device &25 requires service, redundancy lost
Tape with excessive error rate was mounted in tape device &25.
Media error detected by tape device &25.
A non supported device configuration was detected.
Equipment check on library device attached to tape unit &25 (resource &28).
The format of the data for the tape unit &25 is not compatible.
*Attention* A non supported device configuration was detected.
*Attention* Interface error using device &25 (resource &28).
*Attention* Tape device or tape library &25 failed.
*Attention* Tape device or library &25 requires service, redundancy lost.
*Attention* A tape media or tape unit &25 failure was detected.
*Attention* Licensed Internal Code error, device &25.
*Attention* Media error detected by device &25.
*Attention* Tape with excessive error rate was mounted in tape device &25.
*Attention* Licensed Internal Code error.
*Attention* System recovered from temporary I/O error.
Interface error: Device &25 (resource &28)
SCSI interface error: Tape unit &25 (resource &28).
Bus protocol error detected: Tape unit &25 (resource &28).
Equipment check on gateway device.
Licensed Internal Code failure detected by gateway device.
Hardware encryption error.
Hardware configuration change detected.
Tape unit needs cleaning
Operator/CE panel
ACF/OP panel cable
Elevator Assembly
Feeder stage
Pincher mechanism
Roller mechanism
Motor driver card
Elevator servo sensor
Transport magazine interface sensor
Transport drive interface sensor
Global cartridge present sensor
Unused cartridge present sensor
Used cartridge present sensor
Priority slot cartridge present sensor
Magazine present sensor
Home (top) sensor
Magazine lock state sensor
Pinch position 1 sensor
Pinch position 2 sensor
LED card
Bottom flange (reel motor)
Center tape guide
Pneumatic hose kit and compressor
Pantocam or inboard sensor
Pantocam or outboard sensor
Tape lifter solenoid
Tension transducer assembly
Flange, upper (reel motor)
Machine reel guide
Pantocam
Fan (pneumatic)
Fan (power)
Fan (electronics)
Tape path A and B sensors
Power supply AC/DC 36 volts
Tray up and down sensors
Cartridge type or tray down sensors
Tray up or cartridge type sensors
File protect sensor
Door open sensor
Tray up sensor
File protect or door open sensors
Cartridge ID sensor
Tray down sensor
Head guide assembly or BDAT
Head guide or servo card
Deck sensor cable
Power supply cable
Pneumatic sensor cable
Compressor motor cable
Motor driver cable
IPS cable
Actuator/FLASH EEPROM cable
Pressure switch
Card pack
Microcode or WDF
Microcode or WDF
Microcode or RDF
Threader driver or pantocam
Cartridge
RACL card
Accessor
Motor
Picker
Front cover
Motor cable
Picker cable
Sensor cable
Drive/RACL cable
3570 tape drive
Power supply
Cooling fan
AC power cable
SCSI internal cable
Tape device part
Cartridge accessor part
Library part
Tape drive part
RS/422 cable
Accessor assembly
Sensor
Controller logic card
Picker
I/E accessor assembly
I/E assembly
Cleaning cartridge
Test cartridge
Operator Panel/LCD Assembly
Motor Drive
Magazine Lock
RACL Motor Cable
RACL Sensor Cable
RACL Picker Cable
LCD Operator Panel
Media Library Device
Device Licensed Internal Code
EIA-232 communications line
Motor Control Card
Elevator Motor/Gear set
Motor/Gear set
Pinch Shaft
Feed Shaft
Global or Interference sensor
Transport
Priority slot sensor
Random lock sensor
Magazine support
Ribbon cables
OP panel cable
Drive/ACF cable
Cartridge or cartridge type sensor
Tape path outboard sensor
Tape path inboard sensor
Loader sensor
Door open or cartridge type sensor
Threader driver
Device internal cable
Interposer
Internal RS422 interface
SCSI interface
Transport position sensor
Transport cable
Global cartridge present sensor
Global cartridge interference sensor
ACF transport pinch 1 sensor
ACF transport pinch 2 sensor
Pneumatic assembly
Pneumatic hose kit
Fan (card pack)
Flange, lower (reel motor)
Pantocam or tape path B sensor
Pantocam or tape path A sensor
Tray up and cartridge present sensors
Cartridge type or cartridge present sensors
Cartridge type sensor card assembly
Cartridge present sensor
Cleaning cartridge
Media pass/fail criteria not defined
Tape path A sensor
Tape path B sensor
Problem no longer exists
External power supply
Control panel assembly
Control panel cable
Front door assembly
Bar code reader
Magazine mounting plate
Magazine
Check device power and cables
Fibre Channel device
Fibre Channel cable
Gateway device Licensed Internal Code
Gateway device
Fibre Channel IOA
Any Fibre Channel device
Fibre Channel interface
Fibre Channel IOA Licensed Internal Code
Platform dump occurred
I/O adapter owned by VIOS partition.
Encryption Key Manager
Configuration changed, IOP reset required.
IBM 3590 Tape Drive Service Guide
IBM 3590 Tape Drive Operator Guide
IBM 3570 Tape Drive Service Guide
IBM 3570 Tape Drive Operator Guide
Use the sense bytes and 3490 MI to find the failing items
IBM SAN Data Gateway Service Guide
Virtual I/O Server service information.
EKM User's Guide
Controller and device addresses must be less than 15
Unexpected Beginning of Tape encountered during the test
Expected Beginning of Tape not encountered during the test
Expected tape mark not encountered during the test
Device is busy, not available for test
Device is not responding to selection, test can not be run
SCSI command time limit exceeded during the test
SCSI bus interface error occurred during the test
IOP hardware or system bus failure during the test
End of tape encountered before test completed.
The data read does not match the data written during test
Read or write error encountered during the test
IOP Licensed Internal Code failure occurred during the test
Device hardware failure occurred during the test
Unexpected tape mark encountered during the test
Test tape is defective; test can not be run.
Physical End of Media encountered during the test
Tape unit in use by another system; test can not be run.
Device returned invalid status, test can not be run.
Blank tape encountered during the test
Test tape has incorrect data format; test can not be run.
Media or device error occurred during the test
Fibre Channel interface error detected
Gateway device detected a SCSI interface error
Gateway device detected a bus protocol error
Gateway device hardware failure detected
Gateway device LIC error detected
Hardware encryption error encountered during the test
Expansion unit power supply failed
Expansion unit short circuit condition
UEPO switch and cable.
Test is running; please wait
NWID name cannot be found; type new name
The test complete; press the Enter key to continue
Please select a valid option
The test is complete.
Line name cannot be found; type new name
IOP name cannot be found; type new name
Port resource name cannot be found; type new name.
No name was received; type name
No name was received; type IOP name
Remote device cannot be found; enter new name
No name was received; enter remote device name
Invalid value entered. Please enter 1 - 50.
Carrier Detect cannot be displayed at this time.
IOA tests are running; please wait
Ethernet tests are running; please wait
Token Ring tests are running; please wait
Modem tests are running; please wait
Cable tests are running; please wait
Two Port Adapter Cable test is running; please wait
Echo back mode is starting; please wait
Echo back mode is ending; please wait
You typed an *NWI line name, type a non-*NWI line name
TEST FAILED
Multifunction I/O processor storage expansion
Eject personal security card
Resetting IOA; Please wait.
IOA TEST 3 is Running; Please wait.
IOA TEST 4 is Running; Please wait.
System performance problem
Network performance problem
Switched link activation failure message not answered
Transmission groups in the network must be activated
Class-of-service specified does not provide a route
COS acceptable TGs and nodes do not exist for the route
A transmission group on the route could not be activated
Vertical Licensed Internal Code
i5/OS licensed program
Wrong communications controller storage used
Communications IOP address error
Communications IOP instruction not allowed
Communications controller divided by zero
Communications IOP error
Communications IOP interrupt address error
Communications IOP interrupt error
Communications IOP level 1 interrupt address error
Communications IOP level 2 interrupt address error
Communications IOP level 4 interrupt address error
Communications IOP level 5 interrupt address error
Communications IOP level 6 interrupt address error
Communications IOP level 7 interrupt address error
Communications adapter detected storage access error
Communications controller detected not valid data error
Communications IOP cannot write to storage
Wrong communications controller address used
Communications IOP storage access error
Communications IOP card failed
Communications IOP storage test failed
Communications IOP storage failed
Communications IOP test error
Communications IOP storage space not available
Communications controller message error
Communications adapter card failed to run test
*Attention* Missing SCSI jumper card for disk controller.
*Attention* Incorrect SCSI jumper card for disk controller.
Informational only. Resource removed or failed.
I/O card unit
System bus
Communications controller Licensed Internal Code
Bus control unit card
Repair Guide; removal and installation procedures
Data storage address test error
Adapter card read or write-checking error
Adapter card wrong address-checking error
Adapter card processor start-up error
Adapter card processor test failed
Adapter card send or receive test failed
Cannot read adapter card storage
Cannot read adapter card error log
Cannot operate adapter card processor
Adapter card interrupt or reset error
Adapter card check for bad data failed
Adapter card processor error
Wrong value placed in adapter program
Adapter card detected not valid data
Adapter card cannot move data to IOP card
Adapter card test had time-out
Adapter test program not found
Adapter card storage error
Adapter card test had serious error
Unsolicited disconnect mode frame with final set received
Unsolicited unnumbered acknowledge frame received
Frame with an incorrect command field received
Frame with an incorrect format received
Frame with an incorrect NR count received
I-frame with oversized data received
Command collision or bad command sequence from controller
Too many focal points for log indications
Terminal endpoint identifier assignment procedure failed
Terminal endpoint identifier temporarily removed
TEI check procedure failed; TEI removed
Manually assigned TEI removed permanently
Communications IOP task ended abnormally; XIM part
Communications IOP task ended abnormally; PM I/F
I/O card Licensed Internal Code ended abnormally
Loss of synchronization error; threshold limit reached.
Passive bus collision error; threshold limit reached.
DTSE-IN error; threshold limit reached.
DTSE-OUT error; threshold limit reached.
Loss of frame alignment error; threshold limit reached.
Loss of multiframe sync error, threshold limit reached.
Failed activation attempts error; threshold limit reached.
Physical interface could not activate
Physical interface lost activation
Physical interface has not been activated
Loss of received signal message from remote U interface
Loss of power message received from remote U interface
Channelized hardware error detected
Interface hardware error detected
I/O adapter hardware error detected
Local end code violation, threshold limit reached.
Far end code violation, threshold limit reached.
Errored second, threshold limit reached.
Severely errored second, threshold limit reached.
ISDN network topology
Remote terminal equipment
Network equipment
Remote ISDN U interface
ISDN configuration, CHANNEL_TYPE parameter
CHLENTRY values in CRTNWIISDN command
CNNRTY value in CRTNWIISDN command
INTERFACE value in CRTNWIISDN command
DCHLSRV value in CRTNWIISDN command
DCHLENC value in CRTNWIISDN command
Cumulative communication subsystem errors
ISDN channel hardware
ISDN physical interface
I/O card Licensed Internal Code
LCLNBRTYPE value in CRTNWIISDN command
LCLNBRPLAN value in CRTNWIISDN command
SUBADRTYPE value in CRTNWIISDN command
ALRCNNTMR value in CRTNWIISDN command
SETUPTMR value in CRTNWIISDN command
DSCRLSTMR value in CRTNWIISDN command
RLSCMPTMR value in CRTNWIISDN command
RECNNTMR value in CRTNWIISDN command
CALLPRCTMR value in CRTNWIISDN command
TEIDREQTMR value in CRTNWIISDN command
RSRCNAME value in CRTNWIISDN command
CNNACKTMR value in CRTNWIISDN command
LCLSUBTYPE value in CRTNWIISDN command
MAXMSGSIZE value in CRTNWIISDN
INACTTMR value in CRTNWIISDN command
Disconnect retry limit reached
Loss of ISDN Power Source 1 (PS1) detected by adapter
Local token-ring adapter cable
Another adapter card on the same IOP to IOA Bus
Card in line adapter Slot 1
Token-ring diagnostic Licensed Internal Code
I/O card Licensed Internal Code
Repair Guide; removal and installation procedures
Communications IOP cannot read or write to adapter
Communications adapter card test failed
Synchronous-data-link-control send-receive test failed
Communications IOP cannot read adapter card storage
I/O card Licensed Internal Code ended abnormally
Communications adapter card X.21 test failed
Binary synchronous control send-receive test failed
Asynchronous send-receive test failed
Adapter card failed modem interface test
An I/O processor Licensed Internal Code error occurred.
I/O processor Licensed Internal Code error, logged only.
A recoverable I/O processor error occurred.
I/O processor detected a fault condition.
I/O processor detected interface error, logged only.
Disk unit not active
A permanent I/O Processor cache failure occurred.
IOP cache data exists for a missing or failed device.
Array no longer protected due to missing or failed disk unit
Cache mirror card.
IOP &26 failed.
Cache mirror card on IOP &26 failed.
Cache mirror card on IOP &26 failed.
Cache mirror card failed and data loss is possible.
IOP &26 has detected a hardware configuration problem.
The disk units on IOP &26 are not in the expected configuration.
Cache data conflicts with device data on IOP &26
Array protection has been lost on IOP &26.
Disk unit requires initialization before use on IOP &26.
IOP &26 detected a hardware configuration problem.
Array not functional due to present hardware configuration.
Required cache data cannot be located for a disk unit.
IOP &26 detected a Licensed Internal Code failure.
Disk unit is not supported at its physical location.
Device format not set to 522 byte blocks
Device format error reported by I/O Processor &26.
Array not functional on IOP &26 because of hardware configuration.
A permanent cache mirror card failure occurred.
A recoverable cache mirror card error occurred.
IOP &26 indicates a recovered error.
IOP &26 indicates a recovered error.
IOP &26 resources not available.
The disk units on IOP &26 are not in the configuration IOP &26 expects.
The disk units on IOP &26 are not in the expected configuration.
A disk unit on IOP &26 is not supported at its present physical location.
The IOP and attached cache adaptor card are not compatible.
A disk unit that IOP &26 controls has been changed but not by IOP &26.
IOP requires a cache adaptor card but cannot find it.
Array protection temporarily suspended
A device attached to IOP &26 failed.
Cache data exists for device that has been modified.
IOP resources not available due to previous problems.
Disk unit has been modified after the last known status.
Incorrect hardware configuration change has been detected.
Disk unit requires initialization before use.
IOP &26 detected an error in a storage device interface.
The maximum supported number of functional arrays already exist on IOP &26.
Disk expansion unit backplane
Disk unit tray
Disk unit media format corrupted.
Disk unit media format is not correct.
Disk unit sector read error.
Disk unit permanent failure.
Disk unit predicted failure, threshold error type.
IOP predicted hardware failure, threshold error type.
Disk unit error was recovered, statistical error type.
Disk unit data error was recovered, statistical error type.
Disk unit media error was recovered, statistical error type.
Disk unit sector ID was recovered, statistical error type.
Disk unit sector data was recovered, statistical error type.
Disk unit bus error was recovered, statistical error type.
Disk unit sleeve assembly
Disk subsystem configuration error.
Function is running. Go perform the service tasks.
Function is complete.
Device power cable
Card enclosure or backplane
Device terminator
External device cable
Disk drive and carrier
CD-ROM device and carrier
Removable media device and carrier
Internal device cable
Cache adaptor card
*Attention* A critical DASD problem has occurred.
*Attention* A critical system processor problem has occurred.
*Attention* A critical system main store memory problem has occurred.
*Attention* A critical system power problem has occurred.
*Attention* A critical system hardware problem has occurred.
*Attention* A critical system hardware problem has occurred.
A critical system hardware problem has occurred. Critical Message Handler has been run.
Storage I/O adapter
I/O processor timed out a device command
A permanent communications or workstation IOA error occurred
Any PCI card on the PCI bus
Undefined FRU
Device holder
Disk unit holder
Disk unit needs to be formatted
Cache battery pack
Compressed device and compression IOA are not compatible
Device backplane
Operating voltage or temperature range limit exceeded
Expander
Communications adapter card
Adapter card in line adapter slot number minus 1
Token-ring network adapter
Repair Guide; removal and installation procedures
Communications IOP cannot read/write to adapter card
Communications adapter card test failed
Communications controller cannot read adapter card storage
I/O card Licensed Internal Code ended abnormally
IOP &26 failed.
IOP &26 failed.
IOP &26 failed.
IOP &26 failed.
IOP &26 failed.
A device attached to IOP &26 failed.
Device media failure.
IOP &26 failed.
IOP &26 is still operating in a degraded mode.
Communications adapter card
System unit or I/O card unit
Communications IOP card
Adapter card in line adapter slot number minus 1
Repair Guide; removal and installation procedures
Battery Power Unit dates do not match.
Battery Power Unit replacement dates do not match
Error detected in system licensed program
Problem Analysis Guide; VLIC-PIP5
Disk device, service processor, or operating system problem
ISDN call in rejected
Lines not selected
Network interfaces not selected
Communications failure
Service Functions User's Guide; APAR or MTR report
System Operation
Error detected in application program
Device not supported on this system model
DST/SST service tools accessed
Error in constraint enforcement
Device code block error
TCP/IP informational error
Stand Alone DST problem
Error detected in client software
Error detected in client hardware
Client usage problem detected
Error detected at the client
Communications IOP resource not available
Communications IOP start-up failed
Incorrect state in I/O card Licensed Internal Code
I/O card or I/O card Licensed Internal Code error
Repeated single-bit hardware error corrections occurred
Not expected transitions occurred on the modem interface
I/O Regulator.
AC Module in 9406 System Unit power supply.
Cable Carrier, 9406 System Unit.
Card Enclosure, 9406 System Unit.
3.6V Regulator, 9406 System Unit.
Regulator in 280X Disk Unit.
DC Bulk Module.
Battery Power Unit
Blower Assembly
Power Control Compartment (PCC)
SPCN Port Cable
AC Module, SPCN Secondary node.
Expansion Unit/Extension Unit Control Panel
System Exp/Ext card enclosure.
Cable Carrier, 504x feature.
Primary SPCN node Licensed Internal Code.
Secondary SPCN node Licensed Internal Code.
Rack SPCN Licensed Internal Code.
SPCN CEC port fault.
SPCN rack command is not correct.
SPCN node address not correct.
SPCN node address not correct.
Save/Restore device, tray asm.
Model D35-D45 System card enclosure.
System Unit Control Panel
Service Processor Card
SPCN Rack-to-Rack cable
Battery Power Unit fault.
One of the regulators in the 9406 System Unit.
No address assigned to an SPCN secondary node.
One of the loads on the 28V line from I/O Regulator 1.
One of the loads on the 28V line from I/O Regulator 2.
One of the loads on the 28V line from I/O Regulator 1.
One of the loads on the 28V line from I/O Regulator 2.
Battery Power Unit fault.
The ac module in the 9406 system unit power-supply failed.
The ac module in the power-supply failed.
The ac module in the power-supply failed.
An ac loss has occurred in the 9406 SPCN node.
A cooling problem occurred in the 9406 System Unit.
The 9406 Expansion control panel test failed.
A regulator is missing from the 9406 Expansion unit.
A regulator is missing from the 9406 Expansion unit.
An over-current fault has been detected in the 9406 power-supply.
An over-current fault has been detected in the 9406 power-supply.
The 9406 Expansion unit is missing a dc bulk module.
An over-current fault has been detected by the 9406 power-supply.
A 9406 SPCN Licensed Internal Code error occurred.
Regulator 1 Fault
Regulator 2 Fault
Regulator 3 Fault
Regulator 4 Fault
Regulator 5 Fault
System Unit Save/Restore Device regulator reported a fault.
DC Bulk Module 1 Overcurrent
DC Bulk Module 2 Overcurrent
DC Bulk Module 3 Overcurrent
DC Bulk Module 1 Fault
DC Bulk Module 2 Fault
DC Bulk Module 3 Fault
EPO Circuit Fault
AC Module Failure
Battery Power Unit.
Battery Power Unit Failed
AC Module fault (EEPROM)
SPCN Licensed Internal Code Type not valid.
Cooling Problem.
LCD Test Failed
Regulator 1 Not Present
Regulator 2 Not Present
Regulator 3 Not Present
Device 1 regulator fault.
Device 2 regulator fault.
Overload on the +28 V line from regulator 1.
Overload on the +28V line from regulator 2.
No DC Bulk Module installed.
PCC Overcurrent
Undefined Box Identification
SPCN Licensed Internal Code Reload Required.
SPCN Network Fault
AC Module Fault Failure.
Rack to rack SPCN communications failure.
SPCN secondary node to rack node communications failure.
SPCN Packet Size is not correct.
SPCN secondary node time-out.
SPCN rack node time-out.
SPCN secondary node fault.
Battery Power Unit missing
The ac module in the power-supply failed.
Power Control Line Test Failed
The 504x unit power-supply reported a fault.
AC Loss in the 9406 System Unit.
The SPCN ROS and EEPROM LIC is not compatable.
A Battery Power Unit is not installed in the 9406 system unit.
SPCN BATs in process
Regulator 1 has been turned off by system
Regulator 2 has been turned off by system
Regulator 3 has been turned off by system
Regulator 4 has been turned off by system
Regulator 5 has been turned off by system
Regulator 6 has been turned off by system
The system is running on the Battery Power Unit.
The Battery Power Unit is not fully charged.
Battery Power Unit test is in process.
Battery Power Unit discharge life has been exceeded.
Battery Power Unit install life exceeded.
Download in process
Regulator one has been turned off by the system as requested.
Regulator two has been turned off by the system as requested.
Regulator three has been turned off by the system as requested.
Regulator four has been turned off by the system as requested.
Regulator five has been turned off by the system as requested.
Regulator six has been turned off by the system as requested.
The system unit is now getting power from the Battery Power Unit.
The Battery Power unit is being tested.
The Battery Power Unit in the 9406 needs to be replaced.
The Battery Power Unit in the 9406 needs to be replaced.
The rack address in an SPCN command was incorrect.
The secondary node address in an SPCN command was incorrect.
SPCN command contained an incorrect address.
The SPCN node has bad VPD.
The ac module in the 9406 power-supply reported a failure.
An SPCN secondary node reported a fault.
An SPCN rack node reported a fault.
The SPCN licensed internal code can not be loaded.
The SPCN Licensed Internal Code can not be loaded.
The SPCN licensed internal code can not be loaded.
Undefined box ID, EEPROM test failed
Undefined box ID, Code type mismatch
Undefined box ID, LCD test failed
Unknown box ID
Unknown box ID, Code level mismatch.
The SPCN licensed internal code can not be loaded.
The SPCN Licensed Internal Code can not be loaded successfully.
SPCN status code not defined.
Test of the Battery Power Unit is complete.
Operating System to SPCN time-out.
SPCN rack node command failure.
SPCN time-out.
SPCN time-out.
SPCN time-out.
Rack address field in SPCN command not correct.
Rack Address not valid.
Invalid Node Address.
A command has an invalid address mode.
SPCN VPD Damaged
SPCN Licensed Internal Code not valid.
Rack-to-Rack Communications Failure
SPCN Communications Failure, unit to rack.
SPCN Communications Failure, rack to unit.
Unsupported Packet Size
SPCN Licensed Internal Code is not valid.
Rack Timeout
System Unit SPCN fault.
SPCN Node Fault
Rack Node Fault
SPCN Licensed Internal Code is not valid.
EEPROM Failure
Download Failure
QDS Packet Sequence Error
QDS Block Sequence Error
Invalid Load Type
Undefined Status Code
Battery capacity test completed.
VLIC-SPCN Timeout
APA Failure
Download Initialize Timeout
Download Completion Timeout
Load Damaged Timeout
Rack Address field not valid.
Invalid Address status, secondary node.
Invalid Address Mode status
Invalid Rack Command status
System Unit SPCN Port Fault status.
Address Unassigned status
Rack-to-Rack Communications Failure
Intrarack Communications Failure
Power-supply failure in the 504x Expansion Unit.
Unsupported Packet Size status
SPCN Secondary Node Timeout status
Rack Timeout status
Slave Node Fault
Rack Node Fault
ASA Failure
Response Stack Overflow
Response Overrun
No Free Entries
ARA Failure
Undefined status
BCC Fault
Length Check Error.
Undefined status
Configuration Error
Invalid Packet Length for data sent from the PCC.
Power-supply failure in the 504x Expansion Unit.
Power-supply failure in the 9406 system unit.
Power-supply failure in the 9406 system unit.
Power-supply failure in the 9406 system unit.
Power-supply failure in the 9406 system unit.
SPCN rack node fault.
SPCN secondary node address not correct.
SPCN packet length not correct.
SPCN response stack overflow.
SPCN response overrun.
SPCN - no free entries
SPCN Assign Rack Address command failed.
SPCN status code not defined.
SPCN BCC error.
SPCN message length error.
SPCN status not defined.
SPCN configuration error.
SPCN packet length not valid.
An SPCN LID was not found.
An SPCN microcode download is required.
A status change occured in one of the SPCN nodes.
A matching LID for an SPCN node could not be found.
An SPCN node needs the Licensed Internal Code reloaded.
There has been a status change in one of the SPCN nodes.
An fault has been detected in the 504x Expansion power.
A fault has been detected in the 504x Expansion power.
A fault has been detected by the 504x Expansion power.
A Battery Power Unit is not installed.
A Battery Power Unit needs to be replaced.
A Battery Power Unit needs to be replaced.
Failing SPCN node
SPCN node microcode
Card enclosure assembly
Cable carrier assembly
The ac module in the power-supply failed.
A cooling problem occurred in the 504x unit.
DC Bulk Module 3 Fault
DC Bulk Module 2 Fault
DC Bulk Module 1 Fault
DC Bulk Module 1 Fault
DC Bulk Module 2 Fault
DC Bulk Module 1 Over-current
DC Bulk Module 2 Over-current
DC Bulk Module 3 Over-current
DC Bulk Module 1 Over-current
DC Bulk Module 2 Over-current
Repair and Parts; removal and installation procedures
DC Bulk Module 3 Over-current
DC Bulk Module 3 Fault
Fan assembly.
A rack was dropped from the SPCN configuration.
A rack was added to the SPCN configuration.
A rack was dropped from the SPCN configuration.
A rack has been added to the SPCN configuration.
9402 Power Supply.
9402 power fault
Device 3 regulator fault.
Device 4 regulator fault.
D-SE regulator fault.
DC Bulk Module over-current.
DC Bulk Module fault.
Cooling problem in the 5032.
D-SE regulator not present.
Rack UEPO switch is OFF.
Licensed Internal Code part number is not correct.
Battery Power Unit capacity test failed.
SPCN is too large for VLIC.
Regulator 1 in the 5032 reported a fault.
Regulator 2 in the 5032 reported a fault.
Regulator 3 in the 5032 reported a fault.
Regulator 4 in the 5032 reported a fault.
Regulator in the 5032 D-SE box reported a fault.
The DC Bulk Module in the 5032 power-supply reported a fault.
The DC Bulk Module in the 5032 power-supply reported a fault.
UEPO signal active in 504x.
The AC module in the 5032 power-supply failed.
The AC module in the 5032 power-supply failed.
AC module in the 5032 power-supply failed.
No cooling fans installed on the back of the 5032.
A regulator is missing from the 5032 power-supply.
The 5032 box is missing a DC Bulk Module.
A fault has been detected by the 5032 power-supply.
A Licensed Internal Code error occurred in the 5032 power-supply.
The 5032 power-supply control panel test failed.
The part number of the SPCN LIC is not correct.
The Battery Power Unit capacity test failed.
SPCN is too large for VLIC to service.
Rack UEPO switch is OFF.
5032 Cable Carrier.
Rack Control Panel cable.
One of the regulators in the 5032 Unit.
D-SE Converter Module.
Save/Restore device, tray asm.
Vertical Licensed Internal Code.
Control Panel on 5032 box.
The AC Module in the 5032 power-supply failed.
Rack Control Panel.
The 9406 System Unit power-supply reported a fault.
The 5032 power-supply reported a fault.
Voltage too low on 24 volt supply in system unit.
Feature voltage error in system unit.
Current more than limit; 24 volt supply in system unit.
Logic regulator error in system unit.
Unit emergency power off in system unit.
Voltage too high on 24 volt supply in system unit.
AC power error in system unit.
DC Bulk Module 1 is not installed.
System unit power failure.
DC Bulk Module 2 is not installed.
DC Bulk Module 3 is not installed.
DC Bulk Module 1 not installed.
DC Bulk Module 2 not installed.
DC Bulk Module 3 not installed.
DC Bulk Module 1 not installed.
DC Bulk Module 2 not installed.
DC Bulk Module 3 not installed.
AC Module failure.
A command to an SPCN node was rejected.
Addressed Unit not in rack.
Addressed Unit exists, but rack is powered off.
Battery Power Unit is reporting a low charge.
Battery Power Unit is defective.
Battery Power Unit test was aborted.
Addressed rack is not in SPCN configuration table.
Primary SPCN node is reporting load damaged.
Secondary SPCN node is reporting load damaged.
A command to an SPCN node was rejected.
An addressed unit is not in the rack.
A command was rejected because rack is powered off.
Battery Power Unit is defective.
The Battery Power Unit is not fully charged.
Battery Power Unit test was not completed.
Rack not in configuration table.
Load damaged and LID not found.
Load damaged and LID not found.
Secondary SPCN node timeout.
Rack SPCN node is reporting load damaged.
Load damaged and LID not found.
One of the cards powered by I/O Regulator 1.
One of the cards powered by I/O Regulator 2.
Expansion Unit Control Panel
Expansion Unit control panel cable.
Detected AC loss
SPCN Command rejected by the Service Processor.
SPCN - Control Panel interface failure.
SPCN - Control Panel interface is now working.
Overload on the +28 V line from the I/O Regulator.
An over-current fault has been detected in the 9406 power-supply.
One of the cards powered by the 3.6 volt regulators.
One of the cards powered by the I/O Regulator.
One of the loads on the 28V line from the I/O Regulator.
Processor cannot communicate with the bus extension unit
AC Module (5040 unit)
Power Supply
DC Bulk Module
I/O Regulator Card (5040 unit)
Any card in Card Enclosure
Card Enclosure (5030 unit)
Control Panel (5030 unit)
Vertical Licensed Internal Code (5030 or 5040 unit)
Critical fault in ac Module.
AC module in the system unit power supply.
Power Problem in the 9337.
Power problem in a 9337.
Install Disk Unit 1
Power regulator card fault in the System Unit.
Base Power Failure
System Unit Base power supply over current.
System Unit Feature power supply over current.
System Unit Base power supply fault.
System Unit Feature Power supply fault.
SPCN node failure reported in base power supply.
System Unit Battery Power Unit Failed.
Battery Power Unit Failed
SPCN node failure(EEPROM).
SPCN Licensed Internal Code Type not valid.
Power Control Line Test Failed
Battery Power Unit missing in the System Unit.
Battery Power Unit discharge life has been exceeded.
Battery Power Unit install life exceeded.
SPCN Licensed Internal Code Reload Required.
SPCN Network Fault
SPCN node Fault Failure.
An undefined critical fault was detected by the SPCN.
Power Regulator card(9404 System or Expansion Unit)
Power Control cable, System Expansion Unit
POR Circuit fault was detected in the System Unit.
A tray circuit fault(I/O) was detected by SPCN.
Power Regulator card fault in the System Expansion Unit.
System Expansion Unit Base power supply over current
System Expansion Unit Feature power supply over current
System Expansion Unit Base power supply fault.
System Expansion Unit Feature Power supply fault.
SPCN node failure reported in the base power supply.
System Expansion Unit Battery Power Unit is bad.
System Expansion Unit Battery Power Unit Failed.
SPCN node failure(EEPROM).
Battery Power Unit missing in the System Expansion Unit
Battery Power Unit discharge life has been exceeded.
LCD Test Failed
SPCN node Fault Failure.
POR Circuit fault was detected in the System Expansion Unit.
Expansion Unit tray circuit fault.
Expansion Unit Control Panel
System Unit Control Panel Card Assembly
Expansion Unit Control Panel Card Assembly
Base Power Supply
Feature Power Supply
Cable Carrier, System Unit without RAID.
Cable Carrier, System Expansion Unit without RAID.
System Unit board assembly G51 and G61 with RAID
System Expansion Unit Board assembly without RAID
One of the cards powered by the Power Regulator card.
Base power supply
Feat power supply p/n's
Planar Board
System Unit SPCN Licensed Internal Code.
Expansion Unit SPCN Licensed Internal Code.
Cable carrier assembly
SPCN node microcode
A regulator in the System Unit is the failing item
Address not valid.
A command has an invalid address mode.
Addressed Unit not in frame.
Addressed Unit exists, but the frame is powered off.
SPCN Licensed Internal Code is not valid.
Addressed frame is not in SPCN configuration table.
Frame-to-Frame Communications Failure
Unsupported Packet Size
Frame Timeout
System Unit SPCN fault.
Frame Node Fault
Invalid Packet Length for data sent.
A frame was dropped from the SPCN configuration.
A frame was added to the SPCN configuration.
Assign Permanent Address command failure
Frame SPCN node is reporting load damaged.
Frame Address field not valid.
Invalid Frame Command status
System Unit SPCN Port Fault status.
Frame-to-Frame Communications Failure
Frame Timeout status
Invalid Packet Length for data sent.
ARA Failure
Invalid Packet Length for data sent.
Failing SPCN node
A regulator in the Expansion Unit is the failing item
System Unit Board assembly model G46 with RAID
A tray bulk that was on line was turned off.
Secondary Node Fault
AC Module, and/or Base Power Supply. SPCN Secondary Node.
Base Power Supply or a Power Control Compartment (PCC).
SPCN Frame-to-Frame or PCC port cable.
System Unit board assembly G51 & G61 without RAID
System Expansion Unit Board assembly with RAID
Cable Carrier, System Unit with RAID.
Cable Carrier, System Expansion Unit with RAID.
System Unit Board assembly model G46 without RAID
Service processor failure caused machine check interrupt.
SPCN - control panel interface error.
Remote power-on failure
Service processor power-on or auto power restart failure
Manual power-on failure
SPCN power on failure.
Failure of CEC power supply not identified by SPCN.
Battery not working correctly
Service processor error to or from control panel
Interface error.
IPL1 failed in the service processor
Control panel self-test failed
Battery Power Unit needs service
Battery Power Unit needs service.
Battery Power Unit needs service.
Battery Power Unit needs service.
A Battery Power Unit needs to be replaced.
Tray circuit fault.
Install Disk Unit 2
Regulator in the System Unit reported a fault.
Install Disk Unit 3
Install Disk Unit 4
Install Disk Unit K1
Install Disk Unit K2
Install Disk Unit K3
Install Disk Unit K4
Base power supply over current condition has been detected.
Feature power supply over current.
Install Disk Unit K5
Base Power Supply Fault
Feature Power Supply Fault
Install External Disk Unit 6
SPCN node failure in the Base power supply of the System Unit.
Battery Power Unit fault.
A permanent IOP or cache mirror card failure occurred.
SPCN node failure.(EEPROM)
A recoverable IOP or cache mirror card error occurred.
Voltage drop detected on I/O processor 5 volt power supply.
A Battery Power Unit is not installed in the system unit.
The Battery Power Unit in the System unit needs to be replaced.
The Battery Power Unit in the System Unit needs to be replaced.
The System Unit SPCN node reported a fault.
An undefined critical fault was found by the SPCN in the System Unit.
Power on reset circuit error was detected.
A tray circuit fault(I/O) was detected by SPCN.
Regulator in the System Expansion Unit reported a fault
Base power supply over current condition has been detected.
Feature power supply over current.
Base Power Supply Fault in the System Expansion Unit.
Feature Power Supply Fault has been detected in the System Expansion Unit
SPCN node failure in the Base power supply of the System Expansion Unit.
Battery Power Unit fault.
A 9404 SPCN Licensed Internal Code error occurred.
SPCN node failure.(EEPROM)
A Battery Power Unit is not installed.
A Battery Power Unit needs to be replaced.
A Battery Power Unit needs to be replaced.
The Expansion unit control panel test failed.
The System Expansion Unit SPCN node reported a fault.
An undefined critical fault was found by the SPCN in the System Expansion Unit
Power on reset circuit error was detected.
A tray circuit fault(I/O) was detected by SPCN.
The Frame address in an SPCN command was incorrect.
The secondary node address in an SPCN command was incorrect.
SPCN command contained an incorrect address.
An addressed unit is not in the frame.
A command was rejected because the frame is powered off.
Frame not in configuration table.
The System Unit base power supply reported a failure.
An SPCN secondary node reported a fault.
An SPCN frame node reported a fault.
The SPCN Licensed Internal Code can not be loaded successfully.
The SPCN Licensed Internal Code can not be loaded.
The SPCN Licensed Internal Code can not be loaded.
The SPCN node failed.
SPCN status code not defined.
A frame was dropped from the SPCN configuration.
A frame has been added to the SPCN configuration.
Test of the Battery Power Unit is complete.
Operating System to SPCN time out.
SPCN node command failure.
SPCN time-out.
SPCN time-out.
SPCN time out.
The part number of the SPCN Licensed Internal Code is not correct.
The SPCN node has bad VPD.
The Battery Power Unit capacity test failed.
Load damaged and LID not found.
Load damaged and LID not found.
Load damaged and LID not found.
Frame address field in SPCN command not correct.
SPCN node address not correct.
SPCN node address not correct.
SPCN frame command is not correct.
SPCN port fault.
No address assigned to an SPCN secondary node.
Frame to Frame SPCN communications failure.
SPCN secondary node time out.
SPCN frame node time out.
SPCN secondary node fault.
Frame Node Fault
SPCN frame node fault.
SPCN secondary node address not correct.
SPCN packet length not correct.
SPCN - no free entries
SPCN Assign frame Address command failed.
SPCN Assign Address command failed.
SPCN BCC error.
SPCN message length error.
SPCN configuration error.
SPCN packet length not valid.
Optical Library robot arm failure
Optical Library Service Guide
Optical drive failure
Optical Library DASD failure
Configuration exceeds allowed maximum for X.25 lines
Load source tape is not ready
IBM 3995 Maintenance Information, SY32-7034
Communications IOP card
System licensed program
Repair Guide; removal and installation procedures
Clear-to-send state changed; error limit per 256 reached
Carrier-detect state changed; error limit per 256 reached
Call not completed; error limit per 256 reached
Call completed with error; error limit per 256 reached
Data-set-ready state changed; error limit per 256 reached
Incorrect number dialed; error limit per 256 reached
Wrong data block received; error limit per 256 reached
Incorrect data block sent; error limit per 256 reached
Temporary text delay block sent; error limit per 256 reached
Wait-acknowledge block sent; error limit per 256 reached
Communications IOP cannot receive; limit reached
Receive-time-out error; error limit per 256 reached
Incorrect parts installed for BSC communications
Wrong telephone number specified in system configuration
Data-line-occupied initially 'on' error
Communications data trace already active
Automatic call unit has data-line-occupied error
Automatic call unit has distant-station-connected error
Automatic call unit has data-set-ready error
Automatic call unit has call-clear error
Data-set-ready did not drop during time-out
Data-set-ready did not come up during time-out
Port not operational
Automatic call unit has abandon-call attempt
Abandon call retry error; incorrect number length
Automatic call unit power turned off
Communications program error
Incorrect command value in I/O card LIC
Automatic call unit has present-next-digit error
Incorrect command value sent by Licensed Internal Code
Continuous synchronization on line; error limit reached
No synchronization received; error limit per 256 reached
Adapter not installed
V.25 adapter not installed
Call type not permitted
Too many user connections attempted
Call error; incoming call received during outgoing call
Too many dial digits in call setup
Automatic call unit switched link time-out; no answer
Error in I/O card Licensed Internal Code
Storage deallocation error
Storage allocation error
Synchronous time-out; error limit per 256 reached
Hardware detected failure
Communications Management
Vital Product Data Parts
Tape unit formatter failure
Tape unit servo failure
Tape unit motion failure
Control Panel
Write data error: tape path dirty
Read data error: tape path dirty
Tape unit response error; logged only
Tape unit is not responding
Tape unit detected a write error on tape medium
IOP to tape unit interface error; logged only
IOP to tape unit interface error
Illegal or unsupported tape unit response
Blank tape or BOT encountered
Tape unit command timeout
Tape unit detected a read error on the tape medium
7208 Model 012 5.0GB External 8mm Tape Drive Service Guide
Licensed Internal Code for the programmable tape unit
Interface error detected by system or by tape unit
Asynchronous device attached; synchronous device expected
System successfully recovered from temporary I/O error
SPCN panel card
Wait to next IPL or perform TU-PIP4
Problem Analysis
VPD Communication Part
No VPD Found due to Invalid Bypass
Timeout on Panel for Request of VPD
No VPD Found due to Clock Card Failure
VPD Critical Mismatch
Processor Unit VPD Mismatch
Invalid Cache Jumper
Cache Voltage Mismatch
No Processor Installed
Invalid Processor VPD
No Processor VPD
I2C Bus Part
High Speed Link (HSL) I/O bridge
System PCI bus hardware
High Speed Link (HSL) cable, connection or interposer card
Network Interface Controller (NIC)
Multi-adapter bridge
Multi-adapter bridge card slot or card bus
PCI I/O processor or adapter card
I/O tower card
Slot unavailable due to 64 bit card in adjacent slot
High Speed Link (HSL) SPD migration card
System unit backplane
IOA removed from multi-adapter bridge slot
Multi-adapter bridge configuration change or error
LED control failure, do not use slot
Power control failure, do not use slot
Multi-adapter bridge has no IOP for the I/O adapters
Card type not supported in this slot
Local SPD bus adapter
SPD optical bus driver
Remote SPD optical bus receiver on this bus
Remote SPD optical bus receiver on the paired bus
I/O processor removed from multi-adapter bridge card slot
I/O adapter unavailable due to moved I/O processor card
I/O adapter replaced by I/O processor card
Multi-adapter bridge card slot error, do not use card slot
PCI I/O processor rejected assignment or removal of an IOA
LIC has detected an open High Speed Link (HSL) loop
LIC detected High Speed Link resources on unpaired ports
Any card attached to the Multi-adapter Bridge
High Speed Link (HSL) failure
Fiber optic cleaning kit
Optical High Speed Link (HSL) cable or connection
Optical High Speed Link (HSL) failure
Information only, no service action required
Information only, no service action required
Remote HSL OptiConnect system
Local HSL OptiConnect system
Install Disk Unit 5
Other Failing items
Install Disk Unit 6
Install Disk Unit 7
Install Disk Unit 8
Remove Disk Unit 5
Remove Disk Unit 6
Remove Disk Unit 7
Remove Disk Unit 8
Disk Unit 5 regulator has been turned on
Disk Unit 6 regulator has been turned on
Disk Unit 7 regulator has been turned on
Disk Unit 8 regulator has been turned on
Removal of Disk Unit 5 is complete
Removal of Disk Unit 6 is complete
Removal of Disk Unit 7 is complete
Removal of Disk Unit 8 is complete
Disk Unit 5 regulator fault
The regulator in Disk Unit 5 reported a fault
Disk Unit 6 regulator fault
The regulator in Disk Unit 6 reported a fault
Disk Unit 7 regulator fault
The regulator in Disk Unit 7 reported a fault
Disk Unit 8 regulator fault
The regulator in Disk Unit 8 reported a fault
One of the CPM regulators has reported a fault
A Regulator in the System has reported a fault
Regulator over current fault
A regulator has reported an over current fault
Regulator Fault
Regulator fault
Regulator over current fault
Regulator fault
Regulator fault
Regulator fault
A Regulator reported a fault.
One of the CPM regulators has reported a fault
Fan Fault
A problem with a Fan has been detected.
Cooling Problem with one of the blowers
A problem has been detected with a blower
Power supply failure
Power Supply Fault
Power Supply over current fault
Power supply over current
Power Supply P01 error
Power Supply P02 error
Power Supply P03 error
Power Supply P04 error
Power Supply P05 error
Power Supply P06 error
Power Supply P01 Fault
Power Supply P02 Fault
Power Supply P03 Fault
Power Supply P04 Fault
Power Supply P05 Fault
Power Supply P06 Fault
Regulator R01 error
Regulator R02 error
Regulator R03 error
Regulator R04 error
Regulator R05 error
Regulator R06 error
Regulator R07 error
Regulator R08 error
Regulator R09 error
Regulator R10 error
Regulator R11 error
Regulator R12 error
Regulator R13 error
Regulator R14 error
Regulator R15 error
Regulator R16 error
Regulator R17 error
Regulator R18 error
Regulator R19 error
Regulator R20 error
Regulator R21 error
Regulator R22 error
Regulator R23 error
Regulator R01 Fault
Regulator R02 Fault
Regulator R03 Fault
Regulator R04 Fault
Regulator R05 Fault
Regulator R06 Fault
Regulator R07 Fault
Regulator R08 Fault
Regulator R09 Fault
Regulator R10 Fault
Regulator R11 Fault
Regulator R12 Fault
Regulator R13 Fault
Regulator R14 Fault
Regulator R15 Fault
Regulator R16 Fault
Regulator R17 Fault
Regulator R18 Fault
Regulator R19 Fault
Regulator R20 Fault
Regulator R21 Fault
Regulator R22 Fault
Regulator R23 Fault
Configuration or operating system
System unit or I/O card enclosure
Locally attached modem
External devices or network
THRESHOLD value in CRTLINBSC command
MAXBUFFER value in CRTLINBSC command
RSRCNAME value in CRTLINBSC command
ACRSRCNAME value in CRTLINBSC command
INTERFACE value in CRTLINBSC command
LINESPEED value in CRTLINBSC command
CODE value in CRTLINBSC command
AUTOANS, AUTODIAL, DIALCMD, SWTCNN, CNN in CRTLINBSC
CLOCK value in CRTLINBSC command
CNN value in CRTLINBSC command
CNNNBR value in CRTCTL______ command
SNBU, MODEMRATE, INTERFACE values in CRTLINBSC command
Modem attached to remote equipment
CTNRTY value in CRTLINBSC command
DTASTTRTY value in CRTLINBSC command
Data loss because receive buffer full
Protocol error
Locally attached external cable
I/O card Licensed Internal Code resource not available
System processor workload heavy
STXLRC value in CRTLINBSC command
Optical Converter 5V Fault
Configuration Requires 200V Input
Repair Guide; removal and installation procedures
Control language reference manual
Blower B01 powered off for concurrent maintenance
Blower B02 powered off for concurrent maintenance
Blower B03 powered off for concurrent maintenance
Blower B04 powered off for concurrent maintenance
Power Supply P01 powered off for concurrent maintenance
Power Supply P02 powered off for concurrent maintenance
Power Supply P03 powered off for concurrent maintenance
Power Supply P04 powered off for concurrent maintenance
Power Supply P05 powered off for concurrent maintenance
Power Supply P06 powered off for concurrent maintenance
No Power Supplies Present
Clock Regulator Fault
29V Buss Fault
2.5V Processor Regulator Fault
3.3V Processor Regulator Fault
2.5V Memory Control Regulator Fault
3.3V Memory Control Regulator Fault
3.3V Memory 1 Control Regulator Fault
3.3V Memory 2 Control Regulator Fault
Cache Regulator Fault
Processor 1 Regulator Fault
Processor 2 Regulator Fault
Control Supply 5VSW Regulator Fault
Power Supply P01 fault/AC loss
Power Supply P01 fault
Power Supply P01 Communication fault
Power Supply P02 fault/AC loss
Power Supply P02 fault
Power Supply P02 Communication fault
Power Supply P03 fault/AC loss
Power Supply P03 fault
Power Supply P03 Communication fault
Power Supply PP1 Air Moving Device fault
Power Supply PP2 Air Moving Device fault
Battery Charger Load fault
Regulator Fault on Card Position M01
Regulator Communication Fault on Card Position M01
Processor/Memory Card not installed
Processor Regulator fault
Regulator Fault on Card Position M06
Regulator Communication Fault on Card Position M06
SPCN Frame-to-Frame Communication fault
Load fault on the +12V bus
Load fault on the +5V bus
Load fault on the +3.3V bus
Load fault on the -12V bus
Load fault on the +1.8V bus
Load fault on the +2.5V bus
Load Fault on the +12V/-12v bus
Load Fault on the +3.3V/+1.5v bus
Load Fault on the +1.5V/+1.3v bus
Clock Card Failure
Internal Battery Power Unit Charger Fault
Internal Battery Power Unit Fault
Internal Battery Power Unit or Charger Fault
Internal Battery Power Unit Charger Fault
External Battery Power Unit Charger Fault
External Battery Power Unit Fault
External Battery Power Unit or Charger Fault
Air Moving Device Fault
Distant-station-connected error; error limit per 256 reached
Air Moving Device missing error
No cable installed
Break character received; error limit per 256 reached
Received storage overrun; error limit per 256 reached
Incorrect stop bit; error limit per 256 reached
Number of characters discarded; error limit per 256 reached
Wrong data received; error limit per 256 reached
Port already in use
Battery Power Unit 1 and 2 Failed
Wrong configuration value sent by Licensed Internal Code
Wrong number specified in controller description
No number specified in controller description
Port not installed
Automatic call unit port is not installed
Data-line-occupied error at time of starting
Automatic call unit line connection error
Present-next-digit error
Connect time-out; distant-station-connect was not on
Connect time-out, data-set-ready error
Time-out on call-clear-request
Time-out; data-set-ready did not drop
Time-out; data-set-ready not received
Unexpected interrupt
Resource or storage not available
Abandon-call-retry
Abandon-call-retry; not all numbers dialed
Error during get configuration request
Asynchronous server program ended abnormally
Wrong command sent by Licensed Internal Code
Wrong internal routing information
Error in I/O card Licensed Internal Code
Switched line already in use
Trace already active
Wrong length for number dialed
2.5V Processor Domain Fault
3.3V Processor Domain Fault
2.5V Memory Control Domain Fault
3.3V Memory Control Domain Fault
3.3V Memory Control 1 Domain Fault
Automatic call unit distant-station-connected time out
Automatic call unit had data-set-ready time out
Call received during dialing procedure
Communications controller error
3.3V Memory Control 2 Domain Fault
Power Good Fault
MFIOP or Control Panel Card
AC Module or Central Power Source
FRU Control Panel Kit
Control Panel Battery
Back Plane Unit
Cache Regulator Domain Fault
Processor 1 Regulator Domain Fault
Processor 2 Regulator Domain Fault
Clock Regulator Domain Fault
AC Loss to Power Supply P01 or Power Supply P01 Failure
AC Loss to Power Supply P02 or Power Supply P02 Failure
AC Loss to Power Supply P03 or Power Supply P03 Failure
AC Loss to Power Supply P05 or Power Supply P05 Failure
AC Loss to Power Supply P06 or Power Supply P06 Failure
Domain 1 Fault
Domain 2 Fault
Domain 3 Fault
Domain 4 Fault
Power Supply PP1 fault/AC loss
Power Supply PP1 fault
Power Supply PP1 Communication fault
Power Supply PP2 fault/AC loss
Power Supply PP2 fault
Power Supply PP2 Communication fault
Unable to Collect VPD
Memory Module Misplug
Battery Charger Unit missing
SPCN Configuration mismatch
SPCN Default Configuration loaded
No SRC Translate
Alternate Manual Required
External Netfinity Server 3.3V fault
External Netfinity Server Power Good fault
Integrated Netfinity Adapter fault
External Netfinity Server R485 Communication fault
Reference the Problem Analysis Guide for the SRC displayed.
I2C Bus Controller Communication fault
I2C Bus 1 Communication fault
I2C Bus 2 Communication fault
I2C Bus 3 Communication fault
I2C Bus 4 Communication fault
I2C Bus 5 Communication fault
I2C Bus 6 Communication fault
I2C Bus DASD Backplane 1 Communication fault
I2C Bus DASD Backplane 2 Communication fault
I2C Bus DASD Backplane 3 Communication fault
I2C Bus Adapter Communication fault
I2C Bus PCI Backplane Communication fault
I2C Bus Panel Communication fault
I2C Bus Fan Local Controller Communication fault
I2C Bus Fan Remote Controller Communication fault
I2C Bus SPCN VPD Communication fault
I2C Bus Device Backplane 4 Communication fault
Thermal calibration in progress
BPA A AC loss
BPA B AC loss
BPC A communication failure
BPC B communication failure
A DCA or fan has dropped to N-mode status in MCM subsystem
BPC download failure on BPA A
BPC download failure on BPA B
BPC A cable missing
BPC B cable missing
Cage air flow cooling problem
BPA-A to BPA-B communication fault
Critical logic overtemperature
BPR-1 communication fault
BPR-2 communication fault
BPR-3 communication fault
BPA 350V power failure
BPC to BPD-1 communication fault
BPC to BPD-2 communication fault
BPC to BPR-1 communication fault
BPC AC power loss or phase missing
BPC Room EPO switch has been detected open
BPC UEPO switch is in the bypass position
BPA FRU failure not isolated
BPC fault
BPC Seeprom VPD fault
BPF Fan fault
BPD-1 fault
BPD-1 Seeprom VPD fault
BPD-2 fault
BPD-2 Seeprom VPD fault
BPC to BPR-2 communication fault
BPC to BPR-3 communication fault
BPR-1 fault
BPR-1 Seeprom VPD fault
BPR-2 fault
BPR-2 Seeprom VPD fault
BPR-3 fault
BPR-3 Seeprom VPD fault
MCM running over temperature
Airflow loss in MCM subsystem resulting in over-temperature
No MCMs detected or MCMs mismatch
Processor over-temperature detected
Error not isolated; VPD on BPR may be corrupted
Hardware configuration cannot support N-mode power
BPA EPO Switch fault
2.5V bus processor subsystem load fault
1.8V bus processor subsystem load fault
1.5V bus processor subsystem load fault
3.3V bus processor subsystem load fault
5.0V bus processor subsystem load fault
Processor DCA-1 fault
Processor DCA-1 Seeprom VPD fault
Processor DCA-1 cable fault
Processor DCA-2 fault
Processor DCA-2 Seeprom VPD fault
Processor DCA-2 cable fault
Processor DCA-3 fault
Power Controller Part
Power Distribution Part
Power Regulator Part
DC Converter Assembly
Fan and Blower Drive Assembly
MAP Power Problem
Air Moving Device 1 Fault
Air Moving Device 2 Fault
Air Moving Device 3 Fault
Air Moving Device 4 Fault
Air Moving Device 5 Fault
Air Moving Device 6 Fault
Air Moving Device 7 Fault
Air Moving Device 8 Fault
Air Moving Device 9 Fault
Air Moving Device 10 Fault
Power Supply P01 or P02 Overcurrent error
Power Supply P03 or P04 Overcurrent error
Power Supply P01 or P02 Overcurrent Fault
Power Supply P03 or P04 Overcurrent Fault
System Unit Interlock Failure
Secondary Frame Interlock Failure
Power Supply P01 not installed
Power Supply P01 ID is Invalid
Power Supply P02 ID is Invalid
Power Supply P03 ID is Invalid
Power Supply P04 ID is Invalid
Power Good Type S error
Power Good Type M error
Power Good Type P error
Power Good Type I error
Power Good Type S Fault
Power Good Type M Fault
Power Good Type P Fault
Power Good Type I Fault
Air Moving Device Panel Fault
CPM Signal Fault
CPM Regulator 1 Fault
CPM Regulator 2 Fault
CPM Regulator 3 Fault
CPM Regulator Load Fault
CPM Regulator PP1 Fault
CPM Regulator PP2 Fault
UPS Test Failure
UPS unit part
Interlock part
UPS Interface Failure
Power Supply overcurrent
UPS Enable/Disable Failure
UPS CPM Failure
UPS Battery Failure
UPS Unit Failure
Cable Unit Part
Control Supply 5VSW power off failure
Power Good Parts
VPD 5V Power On Failure
VPD 5V Power Off Failure
Air Moving Device B01 Fault
Air Moving Device B02 Fault
Air Moving Device B03 Fault
Air Moving Device B04 Fault
Air Moving Device BP1 Fault
Air Moving Device BP2 Fault
Air Moving Device B01 Not Present
Air Moving Device B02 Not Present
Air Moving Device B03 Not Present
Air Moving Device B04 Not Present
Air Moving Device BP1 Not Present
Air Moving Device BP2 Not Present
Optical Converter
Communications modem interface program
LINESPEED value in CRTLINASC command
ACRSRCNAME value in CRTLINASC command
STOPBITS value in CRTLINASC command
BITSCHAR value in CRTLINASC command
DUPLEX value in CRTLINASC command
AUTOANS, AUTODIAL, DIALCMD, SWTCNN, CNN in CRTLINASC
CLOCK value in CRTLINASC command
THRESHOLD value in CRTLINASC command
PARITY value in CRTLINASC command
CNN value in CRTLINASC command
ECHO value in CRTLINASC command
EORTBL value in CRTLINASC command
FLOWCNTL value in CRTLINASC command
DUPLEX, CNN, MODEMRATE values in CRTLINASC command
CNNNBR value in CRTCTLASC command
Line, modems, remote equipment
Communications line
RSRCNAME value in CRTLINASC command
MAXBUFFER value in CRTLINASC command
SNBU, MODEMRATE values in CRTLINBSC command
SNBU, MODEMRATE, DUPLEX values in CRTLINSDLC command
DUPLEX, ECHO, FLOWCNTL value in CRTLINASC command
Device 2 regulator has been turned on
Device 1 regulator has been turned on
Removal of device 2 is complete
Removal of device 1 is complete
A Battery Power Unit 1 Failed
Battery Power Unit 2 Failed
Battery Power Unit fault.
Battery Power Unit 2 fault.
Regulator 1 fault
Regulator 3 in the system has reported a fault
AC Module fault detection failure
Power regulator 1 card fault in the System
A Regulator in the System reported a fault.
Power regulator 2 card fault in the System
A Regulator in the System reported a fault.
Regulator 2 fault
Power regulator 3 card fault in the System Unit
Regulator 3 in the System unit reported a fault.
A cooling problem occurred in an AC Module
A cooling problem occurred in an AC Module
A card enclosure cooling problem occurred in the System
A storage expansion unit cooling problem occurred
Battery Power Unit 1 fault
Battery Power Unit 2 fault
Battery Power Unit 1 fault
Battery Power Unit 2 fault
Battery Power Unit capacity test failure
The Battery Power Unit 1 has bad VPD
The Battery Power Unit 2 has bad VPD
Remote EPO switch is OFF
Battery Power Unit Charger
SPCN code level does not support the type of BPU installed
Regulator.
Power Supply
Secondary AC Module/BPU charger for Models 530/53S
CPM Regulator 4 fault
CPM Regulator 5 fault
Fan and Blower assemblies
Processor DCA-3 Seeprom VPD fault
Processor DCA-3 cable fault
Processor DCA-4 fault
Processor DCA-4 Seeprom VPD fault
Processor DCA-4 cable fault
Processor DCA-5 fault
Processor DCA-5 Seeprom VPD fault
Processor DCA-5 cable fault
Processor DCA-6 fault
Processor DCA-6 Seeprom VPD fault
Processor DCA-6 cable fault
Processor MDA-1 fault
Processor MDA-1 Seeprom VPD fault
Processor MDA-1 cable fault
Processor Fan 1 fault
Processor MDA-2 fault
Processor MDA-2 Seeprom VPD fault
Processor MDA-2 cable fault
Processor Fan 2 fault
Processor MDA-3 fault
Processor MDA-3 Seeprom VPD fault
Processor MDA-3 cable fault
Processor Fan 3 fault
Processor MDA-4 fault
Processor MDA-4 Seeprom VPD fault
Processor MDA-4 cable fault
Processor Fan 4 fault
BPC-A to BPC-B communication fault
Ambient room temperature limit exceeded
Capacitor card fault
BPC-A and -B are not at standby
UPS utility failure
UPS battery low condition was detected
UPS reported a bypass active
UPS utility power restored
UPS installed
UPS not available
UPS battery low condition was reset
UPS reported bypass no longer active
UPS failure
A permanent IOP or cache adaptor card failure occurred.
A recoverable IOP or cache adaptor card error occurred.
Cache adaptor card.
A permanent cache adaptor card failure occurred.
A recoverable cache adaptor card error occurred.
Cache adaptor card on IOP &26 failed.
Cache adaptor card on IOP &26 failed.
Cache adaptor card failed and data loss is possible.
IOP &26 has detected a hardware configuration problem.
IOP &26 detected a hardware configuration problem.
IOP &26 indicates a recovered error.
Repair Guide; removal and installation procedures
Communications Configuration
Repair Guide; removal and installation procedures
Option not valid at this time
Local Ethernet adapter cable
ADPTADR value in CRTLINETH command
Ethernet network or remote station
Ethernet transceiver
Ethernet network adapter card
I/O card Licensed Internal Code
MAXCTL value in CRTLINETH command
SSAP value in CRTLINETH command
Ethernet controller card load more than limit
Procedure error in I/O card Licensed Internal Code
Input value error in I/O card Licensed Internal Code
Ethernet adapter; remo